Activity Stream

Bought the heads used...so after a valvejob and resurfaced heads, may have been done before. Used the same head gasket as last time FelPro...

yeah 1970 (D0) Lincoln (V) Engine (E), version or revision -C. Any idea what the 1970 pushrod length is? I just wonder if thats where you...

I put on different heads (same head each build)..... Dove-C (the smaller chamber 75cc)Heads. Form what I can tell, thats 1970....have heard guys...

Just like Jaywish said, they don’t. However, I already aimed the old lights before putting in the new ones. The light cutoff is even, so they...

Sorry no tits

Do those fancy lamps have the Hoppy aiming tits on them? hm, that sounds dirtier than it needs to.

There you have it. 567.1 miles on one tank of gas. -ryan s. Sent from my SM-J727P using Tapatalk

betting thats what he was looking at thinking the front panel had to come off or relocate the sensor.

More info here...and even more linked within that thread:...

I’m not aware of it, but my curiosity is piqued. It’s fairly nice to have.

This one any help? http://www.grandmarq.net/vb/showthread.php?27923-Police-pod-install-on-ATC-equipped-vehicle

Not to make more work for you or anything...just wondering if you know about the one touch up/down mod that can me done? Something that can be done...

yeah as long as it doesn't ride on a guide you don't need a hard pushrod. Thats purely for wear resistance. Understand $100 difference in price for...

Gadget, is it ok to skip hardened pushrods sine I don't have guideplates?

Got my headlight relay harness installed since I didn't intend on trying to make H4 bulbs work on the factory wiring, especially with the high beams...

Yeah... remove the nuts/screws from the windshield side of the sensor. Comes right out.

The 8.62 Sealed Power Pushrod I already purchased, came out to that exact length, when checking it with the comp cams pushrod checker. I will make...

The original stuff was basically kraft paper with some sort of coating to make it moisture resistant. Probably could duplicate it with spray...

any reason for not buying the Comp ones in the length you need?

Don't recall removing the front dash trim but its been a long time. I want to say it has two studs that the sensor mounts on and you just remove...

Thanks gadget73. Final question. Removed dash pad which wasn't too bad but it looked as though that one needs to remove front of dash to get...

It was super simple to wire up, and I reused all of my Duraspark III wiring to do it! When the moment of truth came to fire it up with the new...

Ok, I think I figured it out, any comments would be cool. Turns out I never had a 8.55 stock pushrod in my valvetrain. Picture below, left to right:...

Very cool! Nice find

I've seen hypermilers put rope caulk around their headlight housings to fill in gaps to reduce that much more drag. What about a semi truck/trailer...

Front/rear skid plates would also help as it would add some aero as well.

sneaky.

I used some semi thick brown paper and covered it in clear contact paper ages ago. I package tape it into place on the door. Simple and been working...

boat wrap is excellent stuff. Just don't apply a heat gun. Its a shrinking film, so adding heat will make it pull.

right, the lever adjusts tension on a spring inside that gizmo. Its a variable vacuum regulator that is heat sensitive. Its the BS you got in the...

This is where the vacuum gauge comes in. It's been an amazing asset to hypermiling. I'm trying my hardest to keep as much vacuum as possible, since...

Ok. Now I have the full picture. The hot and cold lever moves the ambient air sensor which wasn't apparent to me at first.

It should. Should be a little quicker with higher ratio gears. But just a little.

Woohoo, thanks Kishy.