Announcement

Collapse
No announcement yet.

Ball joint question with pics

Collapse
X
Collapse
 
  • Page of 1
  • Filter
  • Time
  • Show
Clear All
new posts
Previous template Next
    #1

    Ball joint question with pics

    I am test fitting my new lower ball joints (TRW brand for a 1999 Crown Vic) into my 98-02 steering knuckle, and wondering if this is how they are supposed to fit/look when installed.

    only the threads protrude, which I'm assuming is correct, also do these need to be Pressed in?
    1989 Lincoln Town Car - "Anabelle" - Original block, .030 over with SpeedPro pistons, rods fitted with ARP hardware, FRPP +volume oil pump, GT-40 3bar heads, Crane 1.72 rockers, 89' Fox cam, 93' Cobra lower intake, Explorer upper and 65mm TB, 93' Lightning EGR spacer, K&N intake kit from a 4.0L Ranger, 19lb/hr injectors w/ 87 Mark VII ECM, cat/smog deletes, Big Brake conversion, 3.55 K-Code Trac-Lok/Disc brake rear axle, CVPI LCA's w/1" sway bar in rear, wagon front sway bar, BBK 2.5" off-road H-Pipe, Flowmaster super 40s, HPP wheels, 3G alternator w/LMR.com wiring kit, gear reduction starter conversion, Best 1/4 time: 16.0 @ 85mph.
    Tags: None
    #2
    Looks right. The shaft is a taper fit, so cranking the nut down will pull the ball joint in. No press required, its already built in to the ball joint.

    The ball joints do press into the lower arm if thats what you're asking though.
    86 Lincoln Town Car (Galactica).
    5.0 HO, CompCams XE258,Scorpion 1.72 roller rockers, 3.55 K code rear, tow package, BHPerformance ported E7 heads, Tmoss Explorer intake, 65mm throttle body, Hedman 1 5/8" headers, 2.5" dual exhaust, ASP underdrive pulley

    91 Lincoln Mark VII LSC grandpa spec white and cranberry

    1984 Lincoln Continental TurboDiesel - rolls coal

    Originally posted by phayzer5
    I drive a Lincoln. I can't be bothered to shift like the peasants and rabble rousers

    Comment

      #3
      Rent a ball joint press from VatoZone or something like that. It will make this job sooo much easier.
      Originally posted by gadget73
      There is nothing more permanent than a temporary fix.
      91 Mercury CP, Lopo 302, AOD, 3.08LSD. 3g upgrade, Moog wagon coils up front, cc819s in the back. KYB GR-2 police shocks. Energy suspension control arm bushings. Smog deleted.
      93 F-150 XLT, 302, ZF 5-spd from 1-ton, 4wd.
      Daily--07 Civic Coupe. Bone stock with 25k miles
      Wife--14 Subaru Outback. 6-speed.
      95 Subaru Legacy Wagon--red--STOLEN 1/6/13

      Comment

        #4
        I just use a BFH a jack stand and a floor jack.
        1989 Grand Marquis LS
        flat black, 650 double pumper, random cam, hei, stealth intake, Police front springs, Wagon rear, Police rear bar, wagon front ,exploder wheels, 205/60-15 fronts 275/60-15 rears, 1 5/8" headers, 2.5" offroad x pipe, Eclipse front bucket seats, Custom floor shifter, 4.10 gears, aluminum driveshaft and daily driven. 16.77@83mph

        Comment

          #5
          when it doubt... use a bigger hammer.

          Only two things are infinite, the universe and human stupidity, and I'm not sure about the former. -- Albert Einstein
          rides: 93 Crown Vic LX (The Red Velvet Cake), 2000 Crown Vic base model (Sandy), 2003 Expedition (the vacation beast)
          Originally posted by gadget73
          ... and it should all work like magic and unicorns and stuff.
          Originally posted by dmccaig
          Overhead, some poor bastards are flying in airplanes.

          Comment

          Previous template Next
          Working...
          X