PotM GrandMarq.NET - Panther Headquarters Forum Index PotM
GMN Chat Room GMN's STORE!! GMN's Gallery Please!!
Tab Content
  • kishy's Avatar
    Today, 05:57 PM
    Spent a little time with this one today...vacuumed out a bunch of leaves and tree crap, power washed off a layer of dirt, used the special cleaner...
    8 replies | 2875 view(s)
  • kishy's Avatar
    Today, 10:02 AM
    True, not an idiot...thank you lol. I will find out shortly if I'm stuck with the new pump or not. Yes, the plastic ramps are my preferred way...
    686 replies | 59069 view(s)
  • kishy's Avatar
    Yesterday, 07:44 PM
    So, uhhhh...I jumped the gun on deciding that pump was bad. Let's rewind a bit. I wanted to correct the fuel leak, but the tank was full. I had...
    686 replies | 59069 view(s)
  • kishy's Avatar
    Yesterday, 01:13 PM
    Pump died while draining tank to drop it. Electric stuff checks out, pump is getting voltage, but pump is not pumping. I was studying the effects of...
    686 replies | 59069 view(s)
  • kishy's Avatar
    09-25-2020, 07:20 PM
    Fuel pressure even after about an hour of continuous runtime (where a failing pump reveals itself best) is a very solid 39PSI, which sounds about...
    686 replies | 59069 view(s)
  • kishy's Avatar
    09-24-2020, 09:50 PM
    Fuel leak is originating from the area of the fuel pump hanger. I used brake cleaner to clean all the crap off the tank last night and there was...
    686 replies | 59069 view(s)
  • kishy's Avatar
    09-24-2020, 03:38 PM
    On the rear doors of a 4-door car, you are supposed to drill a hole for the screw. The screw threads into the thin sheet metal which forms the rear...
    13 replies | 251 view(s)
  • kishy's Avatar
    09-23-2020, 09:49 PM
    Yeah, the 1qt/1k mi never really sat right with me...especially since they considered that to be normal loss through consumption only, and when the...
    686 replies | 59069 view(s)
  • kishy's Avatar
    09-22-2020, 11:19 AM
    Trunk pan went back in, this time with bigger rivets, and a few bolts. It should be significantly less fragile now. I also managed to make it fit...
    686 replies | 59069 view(s)
  • kishy's Avatar
    09-19-2020, 10:48 PM
    83 and 84 will swap, but 83 and 85 will not for the reason given above. The connector changed. Sensor is electrically compatible but won't plug in.
    5 replies | 166 view(s)
  • kishy's Avatar
    09-18-2020, 04:28 PM
    The above work was lead-up to a bit of a road trip...went camping with some friends a bit north of Parry Sound, ON. Second time to the area, I don't...
    686 replies | 59069 view(s)
  • kishy's Avatar
    09-12-2020, 02:53 PM
    Coming soon, it appears: https://www.facebook.com/230641880120/posts/10164338444280121/ Near perfect clone of mine, so you can bet I'm...
    7 replies | 277 view(s)
  • kishy's Avatar
    09-08-2020, 09:19 AM
    kishy replied to a thread EGR Codes in 5.0/5.8 Engine-Stock
    I have a BOB from a different company, I think Thexton. The round cable has proven to be an issue for exactly that reason, can't close the hood on...
    51 replies | 1654 view(s)
  • kishy's Avatar
    09-07-2020, 10:15 PM
    Worked on a few things today: Wire brushed the rough areas of the passenger rear quarter (spare tire area) to knock loose all the rust chunks....
    686 replies | 59069 view(s)
  • kishy's Avatar
    09-06-2020, 12:20 PM
    kishy replied to a thread EGR Codes in 5.0/5.8 Engine-Stock
    Great troubleshooting! Referring back to my reply...I said 31 is out of spec, not necessarily low ;) It depends where you get the definition from....
    51 replies | 1654 view(s)
  • kishy's Avatar
    09-06-2020, 12:43 AM
    Put in some light highway driving today, cruise is working as it should. Happy about that. Not happy about how far off I managed to make the...
    686 replies | 59069 view(s)
  • kishy's Avatar
    09-05-2020, 01:13 PM
    Good tip about separating the cable from the servo, and also good info about the servo interchange. The 83 has the connectors molded out of what...
    686 replies | 59069 view(s)
  • kishy's Avatar
    09-04-2020, 09:29 PM
    Cruise works! EVTM and shop manual to the rescue, even if I think the problem was maybe something more obvious... Scenario: car has not had...
    686 replies | 59069 view(s)
  • kishy's Avatar
    09-04-2020, 05:13 PM
    It does not come off, unfortunately. That means drilling the old ones out is quite challenging as it's hard to hold this thing in any particular...
    686 replies | 59069 view(s)
  • kishy's Avatar
    09-04-2020, 11:57 AM
    Decided to fix the idle speed. Had to replace defective choke thermostat thing. Had good one in parts. $%#@ More where that came from...
    686 replies | 59069 view(s)
  • kishy's Avatar
    09-02-2020, 09:48 AM
    kishy replied to a thread EGR Codes in 5.0/5.8 Engine-Stock
    Black sensor on both of my EEC-IV CFI cars (84 and 85). I do not know if codes are set on either currently/recently, but I seem to recall there was...
    51 replies | 1654 view(s)
  • kishy's Avatar
    09-01-2020, 12:15 PM
    kishy replied to a thread EGR Codes in 5.0/5.8 Engine-Stock
    If you decide to get rid of CFI, and your disposal method for the CFI parts would not get you any money (e.g. trash can), I would gladly expand my...
    51 replies | 1654 view(s)
  • kishy's Avatar
    08-31-2020, 11:03 PM
    After perusing the EVTM the circuit works like so: Switched power to the hvac function switch, when in any mode except off, power then flows to...
    686 replies | 59069 view(s)
  • kishy's Avatar
    08-31-2020, 03:00 PM
    I would not say I dug deep at all...the part replaced is the mount for the driver wiper, which is easy to get at without removing anything. Now,...
    686 replies | 59069 view(s)
  • kishy's Avatar
    08-31-2020, 11:43 AM
    kishy replied to a thread EGR Codes in 5.0/5.8 Engine-Stock
    31: the voltage the computer sees coming back from the EVP is out of spec (too low or too high to be in the valid range of values). This is an...
    51 replies | 1654 view(s)
  • kishy's Avatar
    08-31-2020, 08:59 AM
    Where the shaft runs through the molded plastic mounting part, they develop play. I believe it's mostly the plastic getting chewed up over time, but...
    686 replies | 59069 view(s)
  • kishy's Avatar
    08-30-2020, 11:00 PM
    When mounting the hitch on the Lincoln, the forward mounting bolts called for the use of existing openings in the frame, and those existing openings...
    686 replies | 59069 view(s)
  • kishy's Avatar
    08-28-2020, 03:32 PM
    This is it mocked up, with the rear bolt in the existing hole in the frame which is ever-so-slightly too far back. I'd be fine with mounting it...
    686 replies | 59069 view(s)
No More Results
About kishy

Basic Information

Age
30
About kishy
Location:
Windsor, ON
Where are we?:
GMN

Signature



83 GM 2dr POTM 10/2019 | 84 TC POTM 1/2017 & 4/2019 | 85 CS | 85 Ranger +trlr | 86 GM | 91 GM POTM 12/2017 | Junkyards
Gone: 97CV | 83 TC

Statistics


Total Posts
Total Posts
1,843
Posts Per Day
0.76
General Information
Last Activity
Today 06:11 PM
Join Date
02-11-2014
Referrals
1
Home Page
http://kishy.ca/

1 Friend

  1. Master Shake Master Shake is offline

    Member

    Master Shake
Showing Friends 1 to 1 of 1
GMN Approved Links!


www.rockauto.com www.adtr.net