PotM GrandMarq.NET - Panther Headquarters Forum Index PotM
GMN Chat Room GMN's STORE!! GMN's Gallery Please!!

Search:

Type: Posts; User: packman; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.10 seconds.

  1. Replies
    7
    Views
    206

    ....I am the walrus Goo goo g'joob....

    ....I am the walrus
    Goo goo g'joob....
  2. Replies
    7
    Views
    206

    That sounds like a nice CV. I hate working on...

    That sounds like a nice CV. I hate working on snow/ice covered ground. Cardboard soaks through in short order :-/
  3. Thread: My '05 MGM

    by packman
    Replies
    27
    Views
    3,552

    The next time I go to the junkyard for CV parts,...

    The next time I go to the junkyard for CV parts, I will see if they have any CV or MGM (03+) with a dual exhaust. If they still don't have any at the yard, I will cut the single exhaust off of one...
  4. Replies
    175
    Views
    10,417

    That was the mistake I made after pulling the...

    That was the mistake I made after pulling the lopo from the '86 CV; I got rid of most the parts I really needed in an effort to keep the complaints down. Among those parts was the '86 TB. I ended...
  5. Replies
    175
    Views
    10,417

    I don't think so. I have the one from the '86...

    I don't think so. I have the one from the '86 CV; and one from the '90 MGM that I was picking apart; they look the same.
  6. Replies
    245
    Views
    31,609

    Unfortunately, now that the fender is exposed, I...

    Unfortunately, now that the fender is exposed, I feel obligated to clean and paint it.
  7. Replies
    245
    Views
    31,609

    Also relocated the oil/air separator to the...

    Also relocated the oil/air separator to the driver-side frame rail. It was too close to the passenger side header where I had it.
  8. Replies
    245
    Views
    31,609

    I took advantage of the weather on Saturday and...

    I took advantage of the weather on Saturday and organized the passenger side fender a bit. I separated the ignition coil wiring from the harness as I will relocate the coil to the front of the...
  9. Replies
    31
    Views
    2,308

    You may want to check on that alternator; if it's...

    You may want to check on that alternator; if it's stock and has not been replaced. Mine did that when it was dying.
  10. Replies
    4,755
    Views
    574,589

    That became my plan when I get my CV running. I...

    That became my plan when I get my CV running. I was going to park the car during the late Fall and throughout the Winter. I figured that once a month I would start the car up and let it idle for a...
  11. Replies
    3
    Views
    201

    Cleaning Steering Gear

    I'm thinking about cleaning the steering gear and painting it while the old lines are still attached to it. Is this a good idea; or a bad one?
  12. Replies
    4,755
    Views
    574,589

    Nice! First startup; like you fire up the...

    Nice!

    First startup; like you fire up the car every few weeks?
  13. Replies
    245
    Views
    31,609

    53324 53325

    53324

    53325
  14. Replies
    245
    Views
    31,609

    53320 53322

    53320
    53322
  15. Replies
    245
    Views
    31,609

    It's been a while since I updated this thread. ...

    It's been a while since I updated this thread. The engine and trans are in, more than less permanently. Had to mod the driver-side header to clear the cross member (squishing, hammering, and...
  16. Replies
    72
    Views
    3,935

    Congratulations on getting married! I would...

    Congratulations on getting married!

    I would lean towards getting a stock rebuild unless you have some serious mods planned for that MGM. But I will let the more knowledgeable members point you in...
  17. Replies
    118
    Views
    8,143

    Okay; mine are Doug Thorley Tri-Y headers for...

    Okay; mine are Doug Thorley Tri-Y headers for 67-70 Mustang with 351W/C6 combo (part description says automatic). The passenger side on mine has no issues; a little close to the cross member. I...
  18. Replies
    6
    Views
    309

    I will find out. Haven't had too much time to...

    I will find out. Haven't had too much time to mess with the Explorer. My MGM has leaking intake manifold that I hope will make it to the Spring; my Aunt has an '08 Saturn Vue that I'm taking care...
  19. Replies
    118
    Views
    8,143

    Did you have interference at the cross member...

    Did you have interference at the cross member with the forward-most primary tube on the driver side header?

    That's what I found when I used headers made for 67-70 Mustangs with a 351W. If I had...
  20. Replies
    21
    Views
    1,573

    Which brand of OEM replacement intake manifolds...

    Which brand of OEM replacement intake manifolds is good? Dorman? Or some other brand?
  21. Replies
    21
    Views
    1,573

    Yep, gonna be doing the intake manifold in the...

    Yep, gonna be doing the intake manifold in the Spring. Getting a bit of steam coming from the back of hood. I think it's coming from the back of the intake; I saw it bubbling when I first fired up...
  22. Replies
    6
    Views
    309

    2005 Ford Explorer

    This is my Mom's '05 Explorer. A friend sold this SUV to me back in March. I had to get this SUV since the CV project has been delayed for so long. It's powertrain is a 4.0L V6 and it's fairly...
  23. Replies
    118
    Views
    8,143

    You can try Heartthrob Exhaust systems. It...

    You can try Heartthrob Exhaust systems. It appears they still make a catback for the 1994-1996 Caprice/Impala. I went with them 12 years ago when doing the full exhaust on the CV. We took one side...
  24. Thread: Remote Locks

    by packman
    Replies
    1
    Views
    173

    Remote Locks

    Has anybody installed or swapped in the remote locking mechanism from a Whale or another vehicle? There are a lot of Whales at the junkyard I go to and was curious. I will research how the system...
  25. Replies
    11
    Views
    657

    If you remove your tank; you might have to put...

    If you remove your tank; you might have to put new strap studs back in. That's what happened when I replaced my tank. When I went to wrap the straps around; they wouldn't match up to the original...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4
GMN Approved Links!


www.rockauto.com www.adtr.net