PotM GrandMarq.NET - Panther Headquarters Forum Index PotM
GMN Chat Room GMN's STORE!! GMN's Gallery Please!!

Search:

Type: Posts; User: kishy; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    429
    Views
    25,469

    Tonight, replaced the diaphragm in...

    Tonight, replaced the diaphragm in the...uh...cold idle cam unloader. Since it isn't a choke pull-off. But it does use the same part and methodology. But whatever.

    Also replaced TPS (new), ECT...
  2. Replies
    429
    Views
    25,469

    Did not verify anything. It has first and...

    Did not verify anything. It has first and reverse, which means it also has second. It's very likely it could be missing OD, but third is probably still there. As long as it has up to 3, it's street...
  3. Replies
    429
    Views
    25,469

    It's the worst of the ones I have, or at least...

    It's the worst of the ones I have, or at least the valley is so far. Now that the intake is back on I can proceed with the valve covers and not get all the crap from the covers in the valley/ports....
  4. Replies
    9
    Views
    164

    I have a strong feeling that it is not wired...

    I have a strong feeling that it is not wired correctly and if you double check you'll find the issue. I had this problem too and had to repin the connectors, and the problem went away.


    Facing...
  5. Replies
    429
    Views
    25,469

    Well...I attached two scraps together, and I...

    Well...I attached two scraps together, and I can't break them apart. The problem, of course, is that I seem to have "soldered" them together using the welding wire rather than truly made them "become...
  6. Replies
    367
    Views
    23,359

    There are multiple steps on the fast idle cam....

    There are multiple steps on the fast idle cam. The amount of throttle travel I'm seeing when the pedal bumps from presumably stored vacuum is almost enough to catch the first step on the cam. I have...
  7. Replies
    367
    Views
    23,359

    The little plastic vacuum reservoir closer to the...

    The little plastic vacuum reservoir closer to the brake master is my guess. I believe that one is dedicated to emissions controls and therefore is available to the bank of solenoids. Off the top of...
  8. Replies
    367
    Views
    23,359

    An observation that I'll file under "CFI musings...

    An observation that I'll file under "CFI musings that need further investigation":

    I've been noticing that, upon turning the key to run, the gas pedal gets pulled a small distance away from my...
  9. Replies
    429
    Views
    25,469

    Finally unboxed the welder, after it sat for...

    Finally unboxed the welder, after it sat for probably about a year. Confidence is rising. Will play with some scrap first of course.

    Got the trailer hitch off. I cut up the fasteners with a...
  10. Replies
    429
    Views
    25,469

    That approach would make it a lot...

    That approach would make it a lot easier...wouldn't have to get the cuts to line up nicely, just overlap a bit. Access to the rear side from below is pretty bad because of the trailer hitch so that...
  11. Replies
    429
    Views
    25,469

    Well done, re: cutting that section out. I'm...

    Well done, re: cutting that section out.

    I'm reasonably sure from the condition of the tailgate window seal that this rust might have been accelerated by water in the interior side, not from...
  12. Replies
    429
    Views
    25,469

    Ah, yes. The question I keep asking myself. I...

    Ah, yes. The question I keep asking myself.

    I would like to weld it, but I never have welded. I bought a flux-core welder specifically for this project and figure it'll be a learning experience.
    ...
  13. Replies
    429
    Views
    25,469

    I'm sure it would help a great deal,...

    I'm sure it would help a great deal, actually...and if it weren't for the fact that I need both a concealed trunk and want the rear seats usable, I might have tried to find a way to keep it open lol....
  14. Replies
    429
    Views
    25,469

    https://www.youtube.com/watch?v=EgSPsWA5kaY...

    https://www.youtube.com/watch?v=EgSPsWA5kaY
    EgSPsWA5kaY

    I don't understand why the car have no floor?!

    http://i.imgur.com/9V1DlePl.jpg

    http://i.imgur.com/8fuYJzEl.jpg
    ...
  15. Replies
    429
    Views
    25,469

    I did not. I was tempted to, but for some reason...

    I did not. I was tempted to, but for some reason settled on not doing it, probably because it was packed in oil like a brake rotor and cleaning it adequately for the paint to not be a waste would be...
  16. You certainly don't, as he is in Austria. Lol. ...

    You certainly don't, as he is in Austria. Lol.

    FWIW, I've done business with him and all went smooth as can be, and I'd gladly deal with OP again.

    If it comes down to it I can parts-hunt for...
  17. Replies
    429
    Views
    25,469

    Fireworks do nothing for me. Never have. It...

    Fireworks do nothing for me. Never have. It always felt like I needed to seem like I was enjoying myself merely for the benefit of the other people who I felt like were feeling the same way and...
  18. Replies
    9
    Views
    295

    I intend to be present. No dates blocked out yet...

    I intend to be present. No dates blocked out yet for me, but prefer not super short notice. Vehicle TBD...but I think we all know what I'm hoping it'll be.
  19. Replies
    926
    Views
    101,029

    Wow. That looks better than I imagined when you...

    Wow. That looks better than I imagined when you told me you wanted to go this route. I am really not fond of the box Vics from most angles, but this is working for me.

    If the bumpers are in...
  20. Replies
    13
    Views
    462

    This is a 1983 non-police Canadian cluster: ...

    This is a 1983 non-police Canadian cluster:

    http://www.grandmarq.net/vb/attachment.php?attachmentid=39314

    As you can see, it goes to 180km/h (about 110mph), but the main unit is km/h.
  21. Replies
    4
    Views
    170

    That should be in one of the two relay boxes at...

    That should be in one of the two relay boxes at the front driver side corner of the engine bay, screwed to the fender. Remove relay box from the fender so it can be flipped upside down, find the...
  22. Replies
    429
    Views
    25,469

    Yeah, the fact they go through the coolant...

    Yeah, the fact they go through the coolant passages really doesn't help with anything. My 91, broke none. 83, broke none. 84, broke one, and I'm fairly sure it was this same one (might have been the...
  23. Replies
    429
    Views
    25,469

    My understanding is that the nylon cam teeth...

    My understanding is that the nylon cam teeth (just the teeth, the gear overall is metal) continued quite a bit later. My buddy's 87 had the nylon stuff.

    My 84 has proven very picky about TV. There...
  24. Replies
    429
    Views
    25,469

    Good question. There is a fair bit of...

    Good question. There is a fair bit of (mis?)information suggesting that it goes to full pressure when the linkage disconnects. When the linkage is disconnected, spring tension at the transmission end...
  25. Replies
    429
    Views
    25,469

    Lincoln's original timing set with nylon-toothed...

    Lincoln's original timing set with nylon-toothed cam gear:

    http://i.imgur.com/B300BCfl.jpg http://i.imgur.com/TYY7Dxwl.jpg

    Take-off from the wagon:

    http://i.imgur.com/PAACZn4l.jpg...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4
GMN Approved Links!


www.rockauto.com www.adtr.net