PotM GrandMarq.NET - Panther Headquarters Forum Index PotM
GMN Chat Room GMN's STORE!! GMN's Gallery Please!!

Search:

Type: Posts; User: 86VickyLX; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.10 seconds.

  1. Converter locks up in 2 3 and 4. 1st no and...

    Converter locks up in 2 3 and 4. 1st no and reverse no.
  2. Torque converter shudder is more so a feeling...

    Torque converter shudder is more so a feeling like running over rumble strips. If it is torque converter shudder, you can verify by lightly applying the brakes to disengage the TCC solenoid.
  3. Replies
    12
    Views
    412

    My suggestion for one with a tired steering box...

    My suggestion for one with a tired steering box would be to do the alignment with the vehicle running. It may help with centering. You're gonna be slightly adjusting to center the play.
  4. Stock shorty headers will clear. You just have to...

    Stock shorty headers will clear. You just have to use 90 degree spark plug boots and heat insulators around the plug boot and wire at the head on cylinders 5, 6 and 7.
  5. Replies
    7
    Views
    542

    I would imagine that the king ranch seats are...

    I would imagine that the king ranch seats are much taller than the panther seats. Might just be an optical illusion. But the though of putting king ranch seats in a vic did cross my mind.
  6. I am running a JL audio 5 channel amp and a...

    I am running a JL audio 5 channel amp and a single 12" JL sub paired with a factory Lincoln (Ford JBL) Tape deck unit. Utilizing the coaxial cable from an 89+ premium sound car, and an adapter from...
  7. Replies
    33
    Views
    7,155

    Sticky: I believe that this is for extra deflection of...

    I believe that this is for extra deflection of water and possibly wind noise reduction.
  8. Replies
    132
    Views
    6,001

    I had that balancer when I built the engine for...

    I had that balancer when I built the engine for Vicky. It ran the engine on the engine dyno at school, but I didn't go further with it because it didn't come with any spacers and I was dealing with...
  9. Replies
    278
    Views
    38,600

    If you are running an a9p, there is no gain to...

    If you are running an a9p, there is no gain to relocating the sensor. And if you do, it's gonna run stupid as it's programmed to be operating in the intake. So you will need that modified in the tune...
  10. Replies
    39
    Views
    1,295

    I will say that the vss input is used for the...

    I will say that the vss input is used for the variable steering assist. It goes to the radio for speed sensitive volume. It also comes through the drivers side firewall from the ecm harness and also...
  11. Replies
    15
    Views
    686

    I like the sound of the older starter. Plus...

    I like the sound of the older starter. Plus they're cheaper.
  12. Replies
    15
    Views
    686

    https://lmr.com/item/SVE-17046K2/Mustang-SVE-130-A...

    https://lmr.com/item/SVE-17046K2/Mustang-SVE-130-Amp-Alternator-Upgrade-87-93-50L nvm I found it. That will all work. Or you can piece it together.
  13. Replies
    15
    Views
    686

    I have used the power wire kit before. It is...

    I have used the power wire kit before. It is plenty of wire to reach on a box. The battery and alternator connections are the same distance apart between the fox and the panther. They don't seem to...
  14. Replies
    39
    Views
    1,295

    I couldn't find any way to run a self test...

    I couldn't find any way to run a self test without some sort of scan tool connected. No documentation that supports it either. Everything mentions superstar tester or equivalent. it's possible that...
  15. Replies
    4
    Views
    293

    We switched them back because you had weird...

    We switched them back because you had weird running problems even with the correct injector specs. They came from my car when I opted to get 60lb DEKA injectors.

    You are 100% correct. Injector...
  16. Replies
    5
    Views
    326

    You need the ecm, the engine harness, the engine...

    You need the ecm, the engine harness, the engine and trans being swapped would be the easiest thing. However, you will need to swap the 84 shift linkage onto the 90 trans, you will also need to get a...
  17. Replies
    278
    Views
    38,600

    Yup! Goes to the vacuum tree on the firewall.

    Yup! Goes to the vacuum tree on the firewall.
  18. Replies
    4,853
    Views
    635,097

    can bus 194 leds solves the cruise issue.

    can bus 194 leds solves the cruise issue.
  19. Replies
    36
    Views
    2,103

    Also forgot to mention the explorers have Pat's...

    Also forgot to mention the explorers have Pat's which disable the vehicles injector pulse. So you would either need to integrate that somehow, or disable it with a tune. Again, pain in the ass.
  20. Replies
    36
    Views
    2,103

    I apologize in advance for the longwinded...

    I apologize in advance for the longwinded response. It's not to deter anyone from trying as I'm in the wiring phase of an OBD-II swap on one of my cars. But just putting the information out there...
  21. Replies
    278
    Views
    38,600

    What setup are you running that the intake hits...

    What setup are you running that the intake hits the wiper motor?
  22. Replies
    36
    Views
    2,103

    I control my 4r70w and 5.0 engine with the use of...

    I control my 4r70w and 5.0 engine with the use of a tuned 94 towncar ecu. You're not really utilizing the mustangs harness. You are using your original with a few added pins. The going rate for an...
  23. Replies
    36
    Views
    2,103

    Maybe we can work something out?

    Maybe we can work something out?
  24. Replies
    36
    Views
    2,103

    Yes, it's been done. I have information that may...

    Yes, it's been done. I have information that may allow the Mustang ECU control cruise control. The hardware is there. It's basically a 90/91 California Mass air car. All you need to do is move the...
  25. Replies
    12
    Views
    797

    Odd because I had to clearance the covers and the...

    Odd because I had to clearance the covers and the end rockers so they didn't hit. Maybe the edelbrock heads are different. I know the crane rockers will clear no problem.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4
GMN Approved Links!


www.rockauto.com www.adtr.net