PotM GrandMarq.NET - Panther Headquarters Forum Index PotM
GMN Chat Room GMN's STORE!! GMN's Gallery Please!!

Search:

Type: Posts; User: gadget73; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.32 seconds.

  1. Replies
    36
    Views
    2,652

    you have no idea how many times I've chased...

    you have no idea how many times I've chased myself in circles only to realize I forgot to plug something in.

    Whats scarier is when I get working on things that are wall powered, go to plug it...
  2. Replies
    42
    Views
    890

    One is for cold starts, the other is to...

    One is for cold starts, the other is to compensate for the extra load of the AC compressor. Why they didn't just have the ECM control the throttle kicker based off the coolant temp sensor, I don't...
  3. Replies
    411
    Views
    37,982

    'bout time it goes under it's own power again

    'bout time it goes under it's own power again
  4. Replies
    62
    Views
    1,649

    I was less concerned about originality as just...

    I was less concerned about originality as just not having to dick about with things that don't fit. Guy at the rad shop had a catalog and having the original in front of him we were able to match...
  5. There is one on the back of each cylinder head. ...

    There is one on the back of each cylinder head. Should be pretty accessible through the trans tunnel with the trans out, but its not inside the bellhouse area.
  6. last one I had done was like 13 years ago and the...

    last one I had done was like 13 years ago and the going price then was about 1200 bucks.

    there are no freeze plugs in the lower manifold. There is one at each end of the cylinder head. There is...
  7. Replies
    42
    Views
    890

    I bet with a little creative fabricobbling you...

    I bet with a little creative fabricobbling you can come up with something to clamp that heater in place. Maybe a tab mounted to something else to give a longer screw something to hold on to. It...
  8. Replies
    62
    Views
    1,649

    the one time I attempted having a rad fixed the...

    the one time I attempted having a rad fixed the guy told me flat out that with as old as the plastic was, it was probably more likely to have the tank crumble when he put it back together than for...
  9. Replies
    6
    Views
    162

    hm, I don't remember having much issue getting...

    hm, I don't remember having much issue getting the card out once the end cap was off. Pretty sure there are no screws or glue or any of that. Maybe needs a jiggle or something to persuade it? Been...
  10. Replies
    62
    Views
    1,649

    chain stretch + plastic tooth wear. All of this...

    chain stretch + plastic tooth wear. All of this is bad.
  11. Replies
    6
    Views
    162

    huh, wouldn't have figured a common ground but...

    huh, wouldn't have figured a common ground but the book tells the story.

    and yeah getting that module out is kind of a PITA.
  12. Replies
    42
    Views
    890

    The pulloff drops the high idle out, the puck has...

    The pulloff drops the high idle out, the puck has an internal spring that engages it. Pull the puck off and make sure the tang didn't break off otherwise it won't engage the linkage. You should...
  13. Replies
    62
    Views
    1,649

    you pulled the washer out right? It absolutely...

    you pulled the washer out right? It absolutely will not go otherwise.

    Should have enough space if you have the fan shroud out. I've used my not particularly compact Kobalt impact to remove mine...
  14. Replies
    21
    Views
    428

    agreed, waste of money. Project Farm on youtube...

    agreed, waste of money. Project Farm on youtube did some filter tests and found that the K&N is less restrictive but also lets more fine particles through. I'll take a bit of restriction to not be...
  15. Replies
    6
    Views
    162

    Inside the keyless entry module are some small...

    Inside the keyless entry module are some small relays. One is for trunk, one is for driver's door, one is for the rest of the doors, and the last is to kick the interior lamps on when you use the...
  16. Replies
    12
    Views
    306

    yep, age and heat are not on your side here. ...

    yep, age and heat are not on your side here.

    Might not be a waste of time to just unplug every electrical connector and gently re-tension the contacts. Anything thats corroded would want a good...
  17. Replies
    42
    Views
    890

    hm, what happens if you ground the STI with the...

    hm, what happens if you ground the STI with the key off and then start the engine?
  18. Replies
    13
    Views
    232

    Welcome. Being from AZ it should be fairly nice....

    Welcome. Being from AZ it should be fairly nice. I've grown to hate rust, especially now that I own two former southern cars and realize what working on vehicles without rot and stuck bolts is like.
  19. Replies
    42
    Views
    890

    Won't help it any if the sensor connectors are...

    Won't help it any if the sensor connectors are crusty.


    If you can seperate 7 and 8 in the wire looms as much as possible it might help. The big key it having space between them, so if you've...
  20. Replies
    2
    Views
    106

    Someone did it on a stock engine a while ago. ...

    Someone did it on a stock engine a while ago. NitrousAl I think? It fits and functions, but I don't know how much you get from it. I sort of remember him saying it killed the low end torque, which...
  21. Replies
    6
    Views
    223

    not much flows at the back. I had a temperature...

    not much flows at the back. I had a temperature gauge back there and it read really odd compared to the normal location gauge.

    Wagonman may also have one if Eddie does not.
  22. Replies
    7
    Views
    241

    I'm never going to advise not upgrading the...

    I'm never going to advise not upgrading the brakes.

    If you're after something a bit different, see if you can get someone to fabricate you a Panhard rod for the rear axle to keep it located under...
  23. Replies
    12
    Views
    306

    full TV pressure at full throttle is probably not...

    full TV pressure at full throttle is probably not far off. My cars with cables all end up pretty near to that point at least. If the trans hits full travel before the throttle body opens full, the...
  24. Replies
    9
    Views
    228

    being me I'd want just the empty plastic shells...

    being me I'd want just the empty plastic shells and the proper terminal ends. Skip the splice entirely, just terminate your wiring right into the shell with the OE type connector terminal. Not sure...
  25. Replies
    6
    Views
    223

    use an 88+ part. No pipe under the intake, its...

    use an 88+ part. No pipe under the intake, its just an extended nipple with a threaded hole in the side for the ECT to screw into. The feed out to the heater core is just a nipple and you can use...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4
GMN Approved Links!


www.rockauto.com www.adtr.net