PotM GrandMarq.NET - Panther Headquarters Forum Index PotM
GMN Chat Room GMN's STORE!! GMN's Gallery Please!!

Search:

Type: Posts; User: sly; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.14 seconds.

  1. Replies
    10
    Views
    143

    De-smogged the 88 SEFI I used to have and it...

    De-smogged the 88 SEFI I used to have and it didn't make any difference at test. This is because on test day, I drive the long way to the inspection station and this gives the cats time to warm up. I...
  2. Replies
    27
    Views
    1,134

    Sounds like the eject mechanism got a little...

    Sounds like the eject mechanism got a little jacked in shipment. There's a switch in the moment of the rack that triggers "tape mode" and it sounds like something is not releasing it. Like a return...
  3. Replies
    527
    Views
    52,950

    "rash" :rofl: Kinda like that aero wagon

    "rash"

    :rofl:

    Kinda like that aero wagon
  4. Replies
    527
    Views
    52,950

    There's something you don't see... ever.

    There's something you don't see... ever.
  5. Replies
    19
    Views
    587

    I think I've only seen them in Fords. And maybe...

    I think I've only seen them in Fords. And maybe only F250. But I know it was fleet only. And probably special order only.
  6. Replies
    19
    Views
    587

    I've seen fleet models in standard cab short bed....

    I've seen fleet models in standard cab short bed. Not sure if you can get that on the consumer side though.
  7. The car books are gone. The rest are still...

    The car books are gone. The rest are still waiting for my wife to make the Goodwill run. No telling when that will be.
  8. Replies
    10
    Views
    258

    This. So much this.

    This. So much this.
  9. Replies
    175
    Views
    10,549

    With the additional air as well as the next step...

    With the additional air as well as the next step injectors... it MIGHT work. Just don't be surprised if it doesn't work. You should probably look into putting a wide band gauge on your setup so you...
  10. Replies
    175
    Views
    10,549

    That bracket should be the same. The cable for...

    That bracket should be the same. The cable for the trans and lever on the throttle body is what's 86 specific.
  11. Replies
    6
    Views
    222

    +1 get the ones that are available and...

    +1 get the ones that are available and plug/close/weld/glue shut the pipe. I also suggest trimming the pipe so not much is hanging off the body of the cat as I had one that hung low and broke itself...
  12. Replies
    19
    Views
    587

    maybe... maybe not. The 100A is a 1G and uses an...

    maybe... maybe not. The 100A is a 1G and uses an external regulator for use on the carbureted models and models with the heated windshield. The 60A could be a 1G low output for base models and...
  13. Thread: Axle Codes

    by sly
    Replies
    4
    Views
    10,366

    Sticky: +1 3.27 open.

    +1 3.27 open.
  14. Replies
    7
    Views
    259

    The light switch should not be mechanically...

    The light switch should not be mechanically locked for an electrical issue. Sounds like something broke in it a popped a fuse. I'd replace the switch and check fuses. Also, it's not hard to replace...
  15. FYI: TV adjustment:...

    FYI: TV adjustment: http://www.txchange.com/aodadj.htm
  16. Replies
    72
    Views
    4,023

    Bad torque converter maybe. Bad trans maybe. Did...

    Bad torque converter maybe. Bad trans maybe. Did you add all the fluid? Should be somewhere around 14 quarts. All the electrical connected?
  17. possible. leakdown and compression tests would...

    possible. leakdown and compression tests would tell for sure. If you have compression on every plug of at least 90psi (preferably ~120psi), it should be able to run and the valves aren't dead.
  18. I hate having to look for a decent mechanic....

    I hate having to look for a decent mechanic. Sounds like you're running into all the reasons I tend to do a lot of my own work.
  19. oh... that one. The worst one. You can still...

    oh... that one. The worst one. You can still remove the spring, drill holes in the plug, or just don't use it and get an aftermarket cooler to mount up front.
  20. Thread: Replace TFI

    by sly
    Replies
    16
    Views
    603

    Most of the store brands are also Standard or...

    Most of the store brands are also Standard or Airtex/Wells and are decent as well.
  21. Replies
    37
    Views
    1,576

    As long as there's good contact area on both...

    As long as there's good contact area on both mating surfaces... it should work well.
  22. Drill the thermostat out. It's basically just a...

    Drill the thermostat out. It's basically just a thermostat past the first or second plate. Or replace it with one that doesn't have a thermostat.
  23. Good to know. And yeah, tune would solve all the...

    Good to know. And yeah, tune would solve all the issues in one go. Ask them if they can delete the stuff you don't have connected before you hand over any $$$ though. Some places can't/won't mess...
  24. Replies
    3
    Views
    207

    Definitely leave the old lines attached while...

    Definitely leave the old lines attached while cleaning/painting.
  25. That might actually work. Not sure if it's a data...

    That might actually work. Not sure if it's a data link (which won't work) or a PWM signal (which would work), but you'll find out I'm sure. I'm genuinely interested to see if that works as I enjoy...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4
GMN Approved Links!


www.rockauto.com www.adtr.net