Search:

This is real true, probably will end up just using Fox headers, since it's a tried and true method. Do you know if they'd bolt up just fine to AFR heads? Kinda planning out my mods, more or less in...

I guess what I'm saying is, with that knowledge, would I need to clearance anything for them? I know headers suck to put on an engine in any engine bay just about, I just don't want to have to cut or...

I guess if I was thinking I would have mentioned that I already have a full custom exhausts and the shop that did it for me expects to make me new downpipes when I get headers. I just couldn't handle...

https://www.summitracing.com/parts/hed-88400/make/ford

Any issues with the install? I've liked every Hedman header I've used before, so I figured I'd give them a look.

A picture of the headliner outside of the car, but I'll give your thread a look.

I could make a fiberglass backer, or reinforce the backing when it's out. In some manner.

I wouldn't mind it...

Hey guys, I've not been able to readily find a picture of headliners out of the car, I know this has to come out to replace my vinyl top, which I need to do. And figured I could tackle multiple...

Stiff, definitely. If my tires had less sidewall, it would likely be edging toward harsh, has a lot more of a 'performance' feel but still doesn't ride like trash and isn't so stiff it's bouncy. I...

Hey, I'll try to post up some pictures soon, I need to do that anyway...

I did end up going with the speedway springs, after doing MORE research around the web of experiences with these being lowered more that that. Judge me all you want for my 'incorrect' :rofl2: spring...

The best knowledge I have says that this makes sense to me as well. Maybe I need to re-read the sticky, and possibly some science type articles somewhere that explains how that works. Other than...

Nice list, and good stance on it. That's the highest I'd like to be, considering I'd like to stay as close to the stock total tire diameter as possible. I do know my speedo reads slightly low right...

I gotcha, that makes sense. I know you can select the spring rate. But what do you mean by load capacity? Like, the size of the actual spring itself? Wouldn't that change based on the spring rate, to...

And general question to all those reading, would this spring work? It seems to have the same outside diameter as the speedway front springs. But is 11 inches tall instead of 12.

11x5.5 OD Springs:...

Oh, sweet manual swap. Glancing at the thread on The Brown Blog a little, what's your suspension setup?

As has been suggested, I will do bushings. But not right this moment. It will happen though, and sway bar(s) for sure. Honestly, I got gas-a-justs because of the price difference. And, just a daily...

So, what you're saying is I could likely go with the step heavier from that and it would still ride decent since the car is heavy. Do you believe that would not be too much, for now? Based on your...

Oh, I do need to start posting a build thread I suppose. That would likely help me keep everything in one place better.

I like my classics, my 1961 Falcon needs love at some point. I have whole...

packman, I've seen you on here. I'll check out the sticky as advised. I scrolled over it lightly at about 2A.M. a couple nights ago. Didn't think to revisit it when I would be conscious enough for it...

So, I already install KYB Gas-a-just shocks. Did wonders for the ride and handling on my 1987 Grand Marquis. Currently running the stock springs, and 86k miles have taken their toll. I can put like...

I've got as Miata that I can't take over speedbumps in the parking garages around here anymore, but how low is your lowest ground clearance sitting level? I don't need two LOW cars, but dang I've...

So, I installed new shocks, they were a pain. Had to cut out the rear shocks with a sawzall by reaching in between the gap in the wheel well with the blade and cutting through the base of the top...

Is it really that simple? I didn't know how it would act with the ECU, didn't want to throw codes and make my car not run.

Hey, I just posted a question about EGR delete on the 5.0, I noticed that your engine bay looks very EGR free. I got a non-egr gt40 upper and lower and wanted to ditch the EGR before I switch over to...

I know there has to be someone who has already gone through the trouble of deleting their EGR stuff, I'd rather know how before I go tearing into it.

I understand fully that there are no power...

Yeah, I'd eventually want to do heads, but don't want to take it that far apart right now. Kinda gathering parts/doing small stuff first.

I've never ran an H or X pipe or any kind of crossover on...