PotM GrandMarq.NET - Panther Headquarters Forum Index PotM
GMN Chat Room GMN's STORE!! GMN's Gallery Please!!

Search:

Type: Posts; User: sly; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.18 seconds.

  1. Replies
    37
    Views
    1,113

    :2up:

    :2up:
  2. Thread: My 88 mgm

    by sly
    Replies
    111
    Views
    5,123

    Nah... your frame is nice... the body on the...

    Nah... your frame is nice... the body on the other hand...
  3. Replies
    225
    Views
    11,113

    That's a roadster. It's got no top. That's just a...

    That's a roadster. It's got no top. That's just a cap to cover the cut off top C pillars. IIRC. Seen it several times before.
  4. Replies
    5
    Views
    229

    good luck was had. Most of the clips (even the...

    good luck was had. Most of the clips (even the crappy prints that were overly smoothed) worked pretty good. Only broke one clip and that was probably from misalignment (not hard to do). Managed to...
  5. Thread: rag joint

    by sly
    Replies
    1
    Views
    48

    One guy just did that and used the 31000 since it...

    One guy just did that and used the 31000 since it was in stock.
  6. Replies
    21
    Views
    716

    Elias was about half way done when I showed up at...

    Elias was about half way done when I showed up at a little after 2. Hopefully he managed to finish the swap. He also has the passenger door molding on the car again. The clips from the 3D printer...
  7. Replies
    4
    Views
    123

    Nope. Open carriers have dished spiders and TL...

    Nope. Open carriers have dished spiders and TL carriers have flat backed spiders... and that's the side spiders that the axles slide into.
  8. Thread: 69 Mak III project

    by sly
    Replies
    12
    Views
    329

    You been TOLD son! :lol3: Yeah... the airbag...

    You been TOLD son! :lol3:

    Yeah... the airbag is completely non-functional in my car and since I think it's the clock spring and safing sensor that need to be replaced, it'll remain a dead system...
  9. Replies
    15
    Views
    205

    Isn't there a u-joint under the brake booster you...

    Isn't there a u-joint under the brake booster you can remove the set screw from?
  10. Replies
    37
    Views
    1,113

    Now I wanna put a good exhaust on my car so my...

    Now I wanna put a good exhaust on my car so my engine can breath and race you. :D
  11. There's a couple different versions IIRC. If you...

    There's a couple different versions IIRC. If you can, post s pic of what you have to help folks know what to look for.
  12. Then it's probably the one-way valve in the fuel...

    Then it's probably the one-way valve in the fuel filter. Those are supposed to be changed every 10-20K miles. I know I'm bad about changing them myself.
  13. If it fires up after sitting for several hours,...

    If it fires up after sitting for several hours, but not after sitting for less than an hour, I would place my bets on heat issue with the TFI module.
  14. Replies
    15
    Views
    313

    If the engine is all original and the timing...

    If the engine is all original and the timing chain hasn't been replaced... do that as soon as you can. The cam gear is made of plastic and will break. A new timing set will give that engine a new...
  15. Replies
    5
    Views
    229

    Elias stepped up. We'll see how this works on...

    Elias stepped up. We'll see how this works on Sunday. I'm hoping to break a few of the new clips and find some that are very durable.
  16. Check the negative battery terminal as well....

    Check the negative battery terminal as well. There should be a small black wire going to it. That's the ground for the ECM. Make sure that's got a good connection. Typically ECM is bad or good and no...
  17. Replies
    5
    Views
    229

    Here's a pic of a few of them. I have 18 clips...

    Here's a pic of a few of them. I have 18 clips currently. We are looking to test this batch and see if any of these clips break. The person that lets me test these on their car will get any needed to...
  18. Could be a sign. Check the relays first. ECA...

    Could be a sign. Check the relays first. ECA relay provides power to all the sensors. If that's not working right, nothing will work.
  19. Replies
    31
    Views
    4,436

    Yes, you want a vacuum on it before cracking the...

    Yes, you want a vacuum on it before cracking the bleeder so that no air is introduced at that moment. It's a just in case maneuver.

    +1 no adjustable wrench. Use a box end.
  20. Replies
    5
    Views
    229

    Clips are in hand. They printed them in various...

    Clips are in hand. They printed them in various orientations. I've discussed slight changes to the model file for better use. Now I need someone with a car that's willing to break a few clips for...
  21. Replies
    5
    Views
    229

    88-91 MGM side trim clips

    I've been talking to a local 3D printing company for the past several months. We are very close to reproducing the 88-91 MGM side trim clip (that nylon bastard that always breaks). I'll be picking up...
  22. Replies
    1,026
    Views
    99,983

    WOOHOO!! Progress! :rtr:

    WOOHOO!!
    Progress!
    :rtr:
  23. Replies
    348
    Views
    21,427

    I don't rub. You know I'm too blunt for that. :D

    I don't rub. You know I'm too blunt for that. :D
  24. Replies
    348
    Views
    21,427

    Once again... I'm glad I live in the land of no...

    Once again... I'm glad I live in the land of no salt.
  25. Replies
    348
    Views
    21,427

    Radioactive mold waste byproduct.

    Radioactive mold waste byproduct.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4
GMN Approved Links!


www.rockauto.com www.adtr.net