PotM GrandMarq.NET - Panther Headquarters Forum Index PotM
GMN Chat Room GMN's STORE!! GMN's Gallery Please!!

Search:

Type: Posts; User: sly; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.16 seconds.

  1. Replies
    17
    Views
    374

    That insulation is around the intake. Without...

    That insulation is around the intake. Without removing the intake, it won't come off. The intake has long runners that loop down into the valley and around to the heads instead of straight in.
  2. Replies
    17
    Views
    374

    04 has the PI engine so it should have the pipe...

    04 has the PI engine so it should have the pipe with o-rings instead of the pipe with the short hose on it. Though the o-rings can go bad eventually, but there's 2 or 3 to go bad.
  3. Replies
    17
    Views
    374

    Right... I did think of checking the fluid level,...

    Right... I did think of checking the fluid level, but didn't type that out. Now for the fun part of finding the leak. Last time I had this happen to me it was a radiator tank crack at the upper hose....
  4. Replies
    17
    Views
    374

    Then you probably have the electronic controls....

    Then you probably have the electronic controls. There's a way to run self diagnostics, but I have no clue how. It's been posted on the forums several times though.
  5. Replies
    17
    Views
    374

    Possibly. If you have the electronic automatic...

    Possibly. If you have the electronic automatic temperature control, it could be an issue with the control head, but I have no clue about those. Others may have ideas about that though. If it's the...
  6. Replies
    17
    Views
    374

    There shouldn't be a flow control valve. If...

    There shouldn't be a flow control valve. If anything, there may be a problem with the blend door not moving all the way or the heater core just not getting good flow (may need a good flush). Check...
  7. Replies
    26
    Views
    1,349

    :lol3:

    :lol3:
  8. Replies
    625
    Views
    77,238

    Poll: :2up:

    :2up:
  9. Replies
    7
    Views
    175

    Nice one. Someone will get a pretty one.

    Nice one. Someone will get a pretty one.
  10. Thread: AOD Rebuild kit

    by sly
    Replies
    6
    Views
    268

    TransGo was the kit put in my AOD in the Mad...

    TransGo was the kit put in my AOD in the Mad Marquis. 60K miles with zero issues.
  11. Replies
    4
    Views
    195

    10/10 would drive. 3/10 would buy. Don't have...

    10/10 would drive.
    3/10 would buy. Don't have room or need.
  12. Replies
    2
    Views
    135

    I would check the radiator fan for anything...

    I would check the radiator fan for anything making contact. Also, if the motor mounts are shot, the fan will contact the shroud. Since it sounds metallic, I doubt that's it though. Next guess would...
  13. Replies
    2
    Views
    248

    Made it to a JY. Got one.

    Made it to a JY. Got one.
  14. I do have that dual core F150 radiator in there...

    I do have that dual core F150 radiator in there and 24 plate trans cooler... so everything stays pretty cool without a lot of effort.
  15. Replies
    4
    Views
    232

    Sounds like the VFD is having issues. Possibly...

    Sounds like the VFD is having issues. Possibly the voltage regulator for the grid. Gets hot and turns off. Might have a loose connection, cold solder joint, or some other issue associated with that...
  16. There's also the option to replace with a 2-wire...

    There's also the option to replace with a 2-wire fan that uses a large resistor for the low speed and completely prevents the both channels on smoke failure.
    Get a 2001-2003 electric fan and...
  17. Replies
    11
    Views
    371

    I did until use used a crow bar to hold the...

    I did until use used a crow bar to hold the alternator at the right tension while tightening the bolts. Me's got skinny arms. Not enough HULK to pull it tight.
  18. You will also need to make sure that both high...

    You will also need to make sure that both high and low fan circuits are not powered at the same time or the new fan will be burned up pretty quick too.
  19. Replies
    2
    Views
    248

    For clarification, I need something smaller than...

    For clarification, I need something smaller than 10x10 if it doesn't have round input and output that I could attach hoses to.
  20. Replies
    2
    Views
    248

    Air filter box/enclosure/assembly

    Anyone in the area (north Texas), have any vehicle air filter box sitting around you want to get rid of? Looking for something that has a flat bottom or round port in and out. Let me know what you've...
  21. Replies
    237
    Views
    14,691

    I wouldn't say the joints are "serviceable" as...

    I wouldn't say the joints are "serviceable" as much as they just like to be a little coated in goop to keep from rusting up.
  22. Replies
    611
    Views
    71,657

    Interesting.

    Interesting.
  23. Replies
    237
    Views
    14,691

    The steering u-joints may also need a little...

    The steering u-joints may also need a little grease and may have just needed a little more movement to be freed up.
  24. Replies
    1,716
    Views
    153,128

    seriously... also... how are the ditch lights...

    seriously... also... how are the ditch lights still in place? Sketchy AF. Parts car.
  25. Replies
    611
    Views
    71,657

    I've seen that + -/+ - 3 wire setup elsewhere....

    I've seen that + -/+ - 3 wire setup elsewhere. IIRC, It essentially runs one side on the low side of an op-amp and the other channel on the high side. Not great for sound reproduction, but decreases...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4
GMN Approved Links!


www.rockauto.com www.adtr.net