PotM GrandMarq.NET - Panther Headquarters Forum Index PotM
GMN Chat Room GMN's STORE!! GMN's Gallery Please!!

Search:

Type: Posts; User: gadget73; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.33 seconds.

  1. Replies
    6
    Views
    123

    Without hearing exactly the sort of rattle you're...

    Without hearing exactly the sort of rattle you're talking about its hard to say.

    agree on scanning it for codes though if all of this started after the TPS got changed. The only thing I can...
  2. Thread: 351W Build

    by gadget73
    Replies
    51
    Views
    4,969

    just make sure they use the same measurement...

    just make sure they use the same measurement system. I made my own adjustable that measured total length and found out that Comp's measuring system is from the centerline of the ball end, not end to...
  3. Replies
    4
    Views
    103

    Supposed to be 11", but not impossible someone...

    Supposed to be 11", but not impossible someone put a sedan rear in. Confirm first, dumb things happen occasionally
  4. Replies
    239
    Views
    24,952

    351 has clearance problems on a Vic with taller...

    351 has clearance problems on a Vic with taller intakes. I don't think its much of an issue on a 302 but I don't have a Vic either.

    Honestly don't know what, if anything, the extra 1/2" or so...
  5. Replies
    4
    Views
    94

    what do you mean exactly? How did you remove the...

    what do you mean exactly? How did you remove the door and its wiring? When I did mine, I fished every inch of wiring out of the door and laid it in the car, then after hanging the door the wiring...
  6. Thread: 351W Build

    by gadget73
    Replies
    51
    Views
    4,969

    I've never actually used a degree wheel, though I...

    I've never actually used a degree wheel, though I probably should have when I changed the cam in my car. Then again I also wasn't 100% sure the valve springs or the p2v clearance was going to be...
  7. Replies
    9
    Views
    179

    if its just dead relays in the LCM, seems to me...

    if its just dead relays in the LCM, seems to me that replacing them ought to make it plenty reliable if the replacements are as good or better than the originals were. Something tells me the...
  8. Replies
    9
    Views
    179

    guessing the autolamp at least sends signal to...

    guessing the autolamp at least sends signal to the LCM to turn the lights on. Not sure when the LCM became a thing though. I thought that was later.
  9. Thread: 351W Build

    by gadget73
    Replies
    51
    Views
    4,969

    wad of clay and an engine rotation is cheap peace...

    wad of clay and an engine rotation is cheap peace of mind tho. Mostly its long duration cams that will cause you problems, not so much total lift. The valves are closing as the piston is coming up...
  10. Replies
    21
    Views
    735

    the lugs are 1/2"-20 on a 5x4.5" bolt circle

    the lugs are 1/2"-20 on a 5x4.5" bolt circle
  11. Replies
    5,009
    Views
    741,967

    the belts are just a thing that has to be dealt...

    the belts are just a thing that has to be dealt with every couple of decades. Not so bad when you change them before they fail, but when it turns to that black sticky goo inside its a real mess to...
  12. Replies
    2
    Views
    108

    I think the breaker is built into the headlamp...

    I think the breaker is built into the headlamp switch, but I don't have an EVTM within reach to confirm.

    wondering if the buzzing is the autolamp relay. If there is a problem in the high beam...
  13. Replies
    9
    Views
    179

    isn't it the little black bump sticking up out of...

    isn't it the little black bump sticking up out of the dash pad on these? Older ones it was under a small perforated area. Either way if you block the sensor the lights are always on.
  14. Replies
    4
    Views
    139

    One of those brackets connects to both the head...

    One of those brackets connects to both the head and the water pump. Distance between the two isn't the same so the bracket changes. Possible its just the upper bracket for the Denso compressor...
  15. Replies
    695
    Views
    84,568

    Poll: Extra hole I'm guessing is one that would have...

    Extra hole I'm guessing is one that would have been used on split bench cars but wasn't on your original solid bench? I know the seats in my car have 4 bolts to the floor.

    Seats look good, and...
  16. Replies
    5,009
    Views
    741,967

    the cleaner tapes work OK for regular maintenance...

    the cleaner tapes work OK for regular maintenance but when they get really crapped up it requires a little more work. usually that only happens on things that haven't been cleaned in a long time, or...
  17. Replies
    5,009
    Views
    741,967

    Have to clean all of the parts though, not just...

    Have to clean all of the parts though, not just the head. The tape runs across a couple of guide pins, and on the capstan and pinch roller. Crud on the head makes it sound flat and dull, crud on...
  18. Replies
    19
    Views
    765

    holy shit, a ghost from the past

    holy shit, a ghost from the past
  19. gunk vs mileage is very hard to determine. Some...

    gunk vs mileage is very hard to determine. Some are spotless with loads of miles, others are full of slime with low miles. Depends on driving style, maintenance, engine condition, planetary...
  20. Replies
    2
    Views
    144

    Yes. The older ones are LH and RH, the later...

    Yes. The older ones are LH and RH, the later ones are the same both sides. Both will fit either spindle, just make sure you get it aligned. I'm using 94 arms and ball joints on mine with a 2000...
  21. Replies
    239
    Views
    24,952

    I have I think a 3/8" spacer. Whatever the...

    I have I think a 3/8" spacer. Whatever the commonly available thinner one is. You will need longer bolts, just keep that in mind. Not all of the kits come with.

    For me its clearance on the...
  22. Pull the studs if you can, its a corrosion thing....

    Pull the studs if you can, its a corrosion thing. Even if you can just get the studs to turn relative to the spacer it will help, but be very careful you don't twist them off in the intake. The...
  23. Replies
    36
    Views
    858

    I can't find the proper section in the parts...

    I can't find the proper section in the parts manual to go with this. There is no listing under 19D896, and in 2888 it says "see 23.1 or 23.2" which my manual doesn't have. The chunk of numbers on...
  24. Replies
    1,850
    Views
    172,043

    There are fees on top f the sell price so it...

    There are fees on top f the sell price so it would have to sell for more than 3k to break even, but if it sold for 3k on BAT, its not likely to sell for grossly more than that a second time if...
  25. Replies
    2
    Views
    225

    What he said. Much is identical, so just watch...

    What he said. Much is identical, so just watch what you spend the effort to swap.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4
GMN Approved Links!


www.rockauto.com www.adtr.net