PotM GrandMarq.NET - Panther Headquarters Forum Index PotM
GMN Chat Room GMN's STORE!! GMN's Gallery Please!!

Search:

Type: Posts; User: johnunit; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.04 seconds.

  1. Replies
    402
    Views
    39,494

    Hey everyone! Been way too damned long. I thought...

    Hey everyone! Been way too damned long. I thought I'd show you a glimpse of the stuff that's come for the car in the last few weeks.

    Not shown is a pair of AFR 185cc heads that were slightly...
  2. Replies
    67
    Views
    6,182

    Looks very clean!

    Looks very clean!
  3. Looks good. I almost wonder if someone could get...

    Looks good. I almost wonder if someone could get good at this and make a little side money pre-building these with junkyard dash pads

    Sent from my SM-G920W8 using Tapatalk
  4. Replies
    20
    Views
    2,537

    I'm in Toronto.

    I'm in Toronto.
  5. Replies
    20
    Views
    2,537

    I may have a rusty old stock civi swaybar...

    I may have a rusty old stock civi swaybar hoarded. You can have it for free if I can find it.
  6. Replies
    54
    Views
    7,135

    That's what I figured. Back to the drawing board.

    That's what I figured. Back to the drawing board.
  7. Replies
    54
    Views
    7,135

    White is on when cranking and red is on in run...

    White is on when cranking and red is on in run and when cranking. Guessing that's how it should be.
  8. Thread: Front air dam

    by johnunit
    Replies
    41
    Views
    6,849

    pics? very curious about undercar aero mods.

    pics? very curious about undercar aero mods.
  9. Replies
    54
    Views
    7,135

    I've swapped back and forth between two ignition...

    I've swapped back and forth between two ignition boxes to confirm they're not the issue, but I think I did end up fixing a connection or two in the initial set of repairs so I guess I should look at...
  10. Replies
    54
    Views
    7,135

    Ah ok. That sounds like stuff I've all dealt with...

    Ah ok. That sounds like stuff I've all dealt with and the timing is stable going by the light. I've had the distributor apart and everything moves nicely.


    I've tried everything from 8 to 15...
  11. Replies
    54
    Views
    7,135

    Took a video to get an idea of what I've got. ...

    Took a video to get an idea of what I've got.

    Short version is it'll run ok at idle with reasonable timing (8+ degrees without vacuum advance, 30-40 with it plugged in) but will hesitate and be...
  12. Replies
    54
    Views
    7,135

    When you say shaft is tight what do you mean?

    When you say shaft is tight what do you mean?
  13. Replies
    54
    Views
    7,135

    New balancer and I've checked that. It does...

    New balancer and I've checked that. It does indeed have multiple timing marks and I checked which was which before mounting. I also confirmed that the vacuum advance cannister on the distributor was...
  14. Replies
    54
    Views
    7,135

    Next stop compression test I guess. Rocker arms...

    Next stop compression test I guess. Rocker arms being pulled is easy enough.



    I couldn't tell for sure due to the slack. It was close but there was enough slack either way to make it show way...
  15. Replies
    54
    Views
    7,135

    Honestly it already had a bearing noise so it's...

    Honestly it already had a bearing noise so it's hard to tell.
  16. Replies
    54
    Views
    7,135

    Finally got everything back together. New comp...

    Finally got everything back together. New comp cams timing gear installed straight up. New oil. All ignition wiring double checked including firing order. Newish cap and rotor. All plugs checked and...
  17. Replies
    17
    Views
    1,862

    FYI the Motorcraft caps are not brass. I can't...

    FYI the Motorcraft caps are not brass. I can't remember what brand I managed to find that was.
  18. Replies
    15
    Views
    3,072

    I'd be curious about drop mounts too, but I've...

    I'd be curious about drop mounts too, but I've never seen any performance mounts for these cars. I agree that easiest would be to just weld something. Normal mounts are cheap. Buy 3 pairs for 50...
  19. Replies
    35
    Views
    4,641

    Would anyone leave rubber in one end of the lower...

    Would anyone leave rubber in one end of the lower rear control arms? I have the full kit and boxed lower arms sitting on a shelf
  20. Replies
    935
    Views
    107,349

    neat

    neat
  21. Replies
    402
    Views
    39,494

    cup style similar to what I posted? Yeah I'm...

    cup style similar to what I posted?

    Yeah I'm definitely fighting the inexplicable sag to one side. Hopefully it'll go away or be reduced with the new springs but I know that's a crap shoot.
  22. Replies
    402
    Views
    39,494

    Interesting. I honestly can't picture what the...

    Interesting. I honestly can't picture what the spring seat looks like beyond a rough guess, so if someone says it works I'll take your word on it. This is all probably going to come out when I lower...
  23. Replies
    402
    Views
    39,494

    yeah these things....

    yeah these things. https://www.summitracing.com/int/parts/mog-k6203-2/overview/

    I suppose if I, say, doubled them up both top and bottom, gluing them together, that'd give me a bit more. I really...
  24. Replies
    402
    Views
    39,494

    Yeah that's what I was worried about. They make...

    Yeah that's what I was worried about. They make spring cup spacers but they seem to be semi-universal which makes me nervous. They have their own pilot thing in the center but who knows if they fit...
  25. Replies
    402
    Views
    39,494

    Cool. I'm not 100% sure I got those when I got...

    Cool. I'm not 100% sure I got those when I got the rear bushings so if not I'll pick those up. Are there supposed to be isolators on the axle side too?

    The current ones are sagged really badly and...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4
GMN Approved Links!


www.rockauto.com www.adtr.net