PotM GrandMarq.NET - Panther Headquarters Forum Index PotM
GMN Chat Room GMN's STORE!! GMN's Gallery Please!!

Search:

Type: Posts; User: packman; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.07 seconds.

  1. Replies
    13
    Views
    226

    That’s basically what I did. I did the fuel pump...

    That’s basically what I did. I did the fuel pump upgrade and the throttle body modification long before I parked the car.
  2. Replies
    13
    Views
    226

    I cut the Holley pump wires and spliced them onto...

    I cut the Holley pump wires and spliced them onto the pump leads because the Holley pump had a plug on both ends; whereas the Panther pump wires has a plug on one end and is held in place by studs on...
  3. Replies
    5,042
    Views
    790,333

    That's funny, as I was looking into a Hero3 a...

    That's funny, as I was looking into a Hero3 a couple years ago and passed it up for reason(s) I can't remember. Crazy how many models are out now. I just need one with decent video and good audio...
  4. Replies
    13
    Views
    226

    Fuel pressure regulator (FPR) adjusts your fuel...

    Fuel pressure regulator (FPR) adjusts your fuel pressure; regardless of your fuel pump volume. Stock FPR is located on the driver side fuel rail.
  5. Replies
    7
    Views
    169

    Those are nice! You can always plumb a catch can...

    Those are nice! You can always plumb a catch can as well; if you don't mind emptying it out every once in a while.
  6. Replies
    7
    Views
    169

    So, I should probably put lopo valve covers on my...

    So, I should probably put lopo valve covers on my junkyard shopping list.
  7. Replies
    262
    Views
    20,708

    That is a nice MGM. Must be the only one in your...

    That is a nice MGM. Must be the only one in your area driving one of them.
  8. Replies
    5,042
    Views
    790,333

    Because of COVID-19; I will be getting a GoPro6...

    Because of COVID-19; I will be getting a GoPro6 or something like that to record the 1st start and anything else after break-in. This is at the request of my friends.
  9. Replies
    7
    Views
    169

    I ran into the exact same issue as you. ...

    I ran into the exact same issue as you. Unfortunately I was given the same options and I opted to cut my wiper box. That was after I had already smashed the wiper motor during the 1st engine...
  10. Replies
    13
    Views
    226

    There is a Sticky thread (Fuel Pump Upgrade) in...

    There is a Sticky thread (Fuel Pump Upgrade) in this forum that outlines what's needed to fit aftermarket pumps into pre-1990 tanks. Sorry, I forgot what year your car is?

    Also, when reading that...
  11. Replies
    357
    Views
    56,105

    I managed to get home while the sun was still up...

    I managed to get home while the sun was still up in the air yesterday; and ground the plugged O2 sensor bung free of the weld. When I sent the exhaust out for welding; he managed to tag the plug. ...
  12. Replies
    13
    Views
    226

    I would go large; just in case you get tired of...

    I would go large; just in case you get tired of the hi-po engine (judging by the "SpeedyEFI" thread) and decide to put something larger in there. At the least; you won't have to switch out the fuel...
  13. Replies
    13
    Views
    226

    Holley/Walbro 255lph pump in mine; but haven't...

    Holley/Walbro 255lph pump in mine; but haven't done the 1st start yet to say how it works (or not).
  14. That one pic with your wagon cleared out makes it...

    That one pic with your wagon cleared out makes it look as if you're getting ready to put out some serious decibels LOL
  15. Replies
    0
    Views
    84

    Unidentified Wire

    Whilst wiring the new alternator; I was going to permanently disconnect the stock regulator plug (the new alternator came with its own plug and wire routing) when I came across a lone wire that comes...
  16. Replies
    5,042
    Views
    790,333

    Box Panther back to terrorizing the neighborhood...

    Box Panther back to terrorizing the neighborhood :D
  17. Replies
    357
    Views
    56,105

    Sinuses were killing me today and they didn't get...

    Sinuses were killing me today and they didn't get any better laying around; so I figured I would get some work done on the CV. Started by installing the starter wiring. Then I moved over to the ACT...
  18. Replies
    172
    Views
    13,481

    Will that wood block stay in place? Other than...

    Will that wood block stay in place? Other than that; awesome work! What did you use for the undercoating?
  19. Replies
    357
    Views
    56,105

    It worked; 3/8"-18 tap. It had just stopped...

    It worked; 3/8"-18 tap. It had just stopped raining when I got home; so I popped the pvc portion off; drilled and tapped it; then reinstalled it. Done deal.

    Tomorrow I will install the starter...
  20. Replies
    357
    Views
    56,105

    Assembled the starter power cable and the signal...

    Assembled the starter power cable and the signal wire last night. Supposed to rain later today; hope to get home before that happens to install them. My Dad went to his friend's place in the next...
  21. Replies
    732
    Views
    92,217

    Poll: Nice!!!

    Nice!!!
  22. Replies
    357
    Views
    56,105

    Wired up the Flex-a-Lite temp sender/switch and...

    Wired up the Flex-a-Lite temp sender/switch and ran the signal wire to the auxiliary fuse box. Then I got to making the CAI up. I thought I'd have more of the pvc run than I ended up with; but it...
  23. Replies
    357
    Views
    56,105

    So I got 1.5" radiator hose with a 90* bend and...

    So I got 1.5" radiator hose with a 90* bend and 6" legs. Cut 1.25" off of one hose and it all fit like a glove. Since the recently bought water pump put the coolant hoses closer to the fuel lines;...
  24. Thread: My '05 MGM

    by packman
    Replies
    67
    Views
    8,793

    Installed one of the catch cans between the valve...

    Installed one of the catch cans between the valve cover and air intake tube. This is a temporary set up as all was had at the local auto parts store was 5/8" heater hose. I will see if I can get...
  25. Thread: 351W Build

    by packman
    Replies
    76
    Views
    8,015

    Mine is fairly large; it was the only one with...

    Mine is fairly large; it was the only one with -AN fittings welded onto it.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4
GMN Approved Links!


www.rockauto.com www.adtr.net