PotM GrandMarq.NET - Panther Headquarters Forum Index PotM
GMN Chat Room GMN's STORE!! GMN's Gallery Please!!

Search:

Type: Posts; User: stinkydogfilms; Keyword(s):

Page 1 of 18 1 2 3 4

Search: Search took 0.01 seconds.

  1. Got the 65 mm throttle body and spacer on. I used...

    Got the 65 mm throttle body and spacer on. I used no sealant.
    I drove 10 miles and it was a blast.
    I noticed the engine seemed to breath easier. Maybe the gas mileage will improve to.
    Less effort...
  2. Thank you Gadget.

    Thank you Gadget.
  3. Thank you Scott and Massacre. I will not use...

    Thank you Scott and Massacre.

    I will not use any sealant and will clean the surfaces will.
    Thank you
  4. Thank you again Sly and Brown_muscle.

    Thank you again Sly and Brown_muscle.
  5. which gasket sealant to use for throttle body and spacer?

    Good day and hope all of you are well,

    I'm going to swap throttle bodies this weekend.
    Which gasket sealant should I use for the throttle body and spacer?
    I do have new gaskets for the swap.
    ...
  6. Replies
    2
    Views
    122

    65 mm tb and 19 lb injectors

    I had TAVR done on Tuesday and came home 18 hours later. This technology is crazy awesome. This replaced my Aortic valve without having to cut open my chest. It only takes 90 minutes. I知 feeling...
  7. Replies
    15
    Views
    1,003

    Good point Gadget. I hope not. This one is very...

    Good point Gadget.
    I hope not. This one is very original from Arizona with low miles. It still has desert dust on it.

    The other 90 wagon is doing well, always starting. Very smooth idle and...
  8. Replies
    15
    Views
    1,003

    I have a set of new rebuilt injectors on the...

    I have a set of new rebuilt injectors on the shelf.
    The car has at least 82,000 miles and thought I might as well do it at the same time.
  9. Replies
    15
    Views
    1,003

    Guess I'll replace the fuel injectors then. I...

    Guess I'll replace the fuel injectors then.
    I didn't want to deal with an intake gasket.
  10. Replies
    15
    Views
    1,003

    Thanks again VCV and BGW. So far the plastic...

    Thanks again VCV and BGW.
    So far the plastic hoses look ok.
    The line coming from the intake is rubber and connects into an adapter fitting that adapts to a smaller hose to the MAP sensor. THANKS...
  11. Replies
    15
    Views
    1,003

    Thank you VCV. I知 looking into using medical...

    Thank you VCV. I知 looking into using medical clamps, the old roach clip kind and a mirror to see what I知 doing coming in from the firewall side. The clamps I have are too large and need to get a...
  12. Replies
    15
    Views
    1,003

    Replace MAP sensor vacum line

    Hi everyone.
    Is it possible to replace the vacuum line to the MAP sensor without removing the intake? The line from the intake is dry rotted and collapses. It痴 probably the original line. It痴 a...
  13. Replies
    7
    Views
    544

    Thank you David. Today I put some Seafoam for...

    Thank you David.
    Today I put some Seafoam for transmissions in, hoping to free up any sticky valves. I drove it around for 33 miles in neighborhood conditions. I manually shifted from 1-2 many...
  14. Replies
    7
    Views
    544

    Thank you Brown Muscle and Gadget. I'm going to...

    Thank you Brown Muscle and Gadget. I'm going to have a look into it this weekend.
    Might be time for a set of wide ratio gears and a little higher stall converter along with a rebuild.
  15. Replies
    7
    Views
    544

    starting off in 2nd gear..90 AOD

    So it seems like the car is starting off in second gear from a stop. What could be the cause? If I pull the gear lever all the way down (2) I have 1st gear and if I floor it in second with the lever...
  16. Replies
    14
    Views
    817

    I'm sorry if I was not clear. The shift from 1st...

    I'm sorry if I was not clear. The shift from 1st into 2nd is at 3800 rpm. The AOD has stock gears. I know the shift should be higher. I have not even checked the WOT shift from 2 to 3 and beyond. The...
  17. Replies
    14
    Views
    817

    I知 going to check with another tach. I thought...

    I知 going to check with another tach.
    I thought it was shifting before at 45 mph with the 3.55s and AOD. I looked again and it looked like 40 mph at 3800.
  18. Replies
    14
    Views
    817

    it actually will break them loose by accident...

    it actually will break them loose by accident sometimes at less throttle than that. I need to dyno it one day. I am curious about the torque. Im guessing the horsepower is around 280.
    When Bernie...
  19. Replies
    14
    Views
    817

    Gadget you nailed it again. A couple of days ago...

    Gadget you nailed it again. A couple of days ago I changed the TPS and the check engine light never came on. I drove 7 miles around the neighborhood with quite a few stop signs. The idle stayed at...
  20. Replies
    14
    Views
    817

    Thank you

    Thank you
  21. Replies
    14
    Views
    817

    I'm not feeling too brave on that. Any advice on...

    I'm not feeling too brave on that.
    Any advice on lowering the 2-3 shift point?
    It's suppose to have a Mustang governor.
    Thanks again.
  22. Replies
    14
    Views
    817

    It does have the flat spot on the lower, but I...

    It does have the flat spot on the lower, but I don't want to pull the intake until I have to, maybe to replace the fuel injectors one day.

    you're so AWESOME Gadget. Thank you Thank you Thank you.
  23. Replies
    14
    Views
    817

    pulled some codes

    Hi, I got around to pulling some codes yesterday.
    This is a 1990 Colony Park with a stock block, 96 Explorer heads and intakes, 90 HO throttle body, 90 Mustang Computer, Mustang headers, 19 lb...
  24. Replies
    10
    Views
    829

    Thank you Gadget. I will check the temperature...

    Thank you Gadget.
    I will check the temperature sensors and report back.
    I appreciate the help.
  25. Replies
    10
    Views
    829

    Thank you David. Believe me we are good and GOD...

    Thank you David. Believe me we are good and GOD was looking after this fool and his family. I pray for those that lost their loved ones and the broken pipes. Everyone should be ok with the water...
Results 1 to 25 of 433
Page 1 of 18 1 2 3 4
GMN Approved Links!


www.rockauto.com www.adtr.net