PotM GrandMarq.NET - Panther Headquarters Forum Index PotM
GMN Chat Room GMN's STORE!! GMN's Gallery Please!!

Search:

Type: Posts; User: sly; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.10 seconds.

  1. Thread: Gain access

    by sly
    Replies
    3
    Views
    68

    take the carpet off the inside of the trunk on...

    take the carpet off the inside of the trunk on that area. That's about the best access as you'll get... and it sucks. If it's closer to the door than the filler neck, you may have to take the back...
  2. Replies
    19
    Views
    404

    I would suspect that would be the case.

    I would suspect that would be the case.
  3. Replies
    11
    Views
    147

    Problem areas that may arise are rubber fuel...

    Problem areas that may arise are rubber fuel lines. The section in the fuel tank from the pump to the hanger, lines that connect to the hanger from the body, stuff near the fuel filter, and the lines...
  4. Replies
    19
    Views
    404

    Nice.

    Nice.
  5. Replies
    318
    Views
    26,210

    If the timing chain has any slack it'll do wonky...

    If the timing chain has any slack it'll do wonky stuff. The original cam gear had nylon teeth, so replacing with standard steel gears fixes that issue. If this has already been done, could just be...
  6. Replies
    19
    Views
    404

    I've had 5 meters with blown current fuses at one...

    I've had 5 meters with blown current fuses at one time... so lack of checking the fuse due to multiple meters with the same goofy reading isn't a good excuse. Check the fuse. It's a sanity check. It...
  7. Replies
    19
    Views
    404

    Yeah, I'm thinking the meter might have a bad...

    Yeah, I'm thinking the meter might have a bad fuse in it.
  8. Replies
    35
    Views
    2,119

    heh... yeah... noting which 10 mark to use is...

    heh... yeah... noting which 10 mark to use is sometimes overlooked when in a hurry to get it working to sell. Looks like you got one of those.
  9. Replies
    19
    Views
    404

    On modern cars, I've seen 300-500mA initially...

    On modern cars, I've seen 300-500mA initially after power down. After 20-60 minutes (depending on the car) it drops to 100mA or less. 100mA is not uncommon in more electronics heavy vehicles.
  10. Replies
    318
    Views
    26,210

    The expy seal is available from Ford... each door...

    The expy seal is available from Ford... each door is about $100 or so. I need ALL of the doors. A bulk type would be much better for me.

    Edit:
    Looks like the 03 F150 supercab seal (163") may be...
  11. +1 dry on a clean and flat surface. If using any...

    +1 dry on a clean and flat surface. If using any RTV, use just a smearing on the gasket surface.

    +1 Ultra gray or Ultra black are the ones to use.
  12. Replies
    318
    Views
    26,210

    Did you happen to note how long each one is? I...

    Did you happen to note how long each one is? I might be able to use this with my Expedition as well. Have to double check the shape of my seals, but I think they're the same. I know the door hole is...
  13. Replies
    21
    Views
    646

    Yeah... my car was originally a LX highway...

    Yeah... my car was originally a LX highway cruiser. I've built it into an HPP except for the springs and sways. I prefer the ride as is with just the KYB Gas-a-justs upgrade.
  14. Replies
    21
    Views
    646

    The wheels on my car are HPPs. They were the BBS...

    The wheels on my car are HPPs. They were the BBS made for Ford "performance" wheels.
    56257
  15. Replies
    6
    Views
    318

    Yeah... +1 blend door actuator. You can...

    Yeah... +1 blend door actuator. You can technically see if behind the glove box, but getting it out... Lots of cussing and possible dash removal. Might be able to get it by pulling the passenger...
  16. Replies
    28
    Views
    3,048

    Sticky: Freecad is still working on the one transform....

    Freecad is still working on the one transform. There's just too much data for a single threaded process I think.
  17. Replies
    6
    Views
    318

    What year is the towny again? I know my 88 MGM...

    What year is the towny again?

    I know my 88 MGM had the autolamp relay there behind the ashtray, but the townies may not have kept it in the same place. I've also heard of the door chime doing...
  18. Need stronger glue to hold the velcro to the...

    Need stronger glue to hold the velcro to the headliner board.

    Wood glue might work well to hold the velcro to the headliner board. Would need to clean the surface on both though.
  19. Replies
    28
    Views
    3,048

    Sticky: Printed it flat with the spring legs flat on the...

    Printed it flat with the spring legs flat on the printing surface and all the support structure under the face of the clip. This one came out better.
    56247 56248

    I'm also trying to get freecad to...
  20. Replies
    28
    Views
    3,048

    Sticky: First print attempt using "eco-abs". Looks...

    First print attempt using "eco-abs". Looks workable. Would prefer nylon, but pretty sure nylon won't have the definition on this printer since it won't do as fine of movements and requires more heat....
  21. It depends on the phone. The site just serves up...

    It depends on the phone. The site just serves up the data. I haven't seen any desktop (full computer) browser rotate anything to "as taken".
  22. Replies
    15
    Views
    446

    oof.

    oof.
  23. Replies
    318
    Views
    26,210

    If you're talking about the bits around the...

    If you're talking about the bits around the headliner, there are metal clips holding it into the body. You should use a trim pry tool to find the clips and then pry them out directly. This will help...
  24. Replies
    15
    Views
    446

    Fancy.

    Fancy.
  25. Mobile vs desktop. Mobile will sometimes use the...

    Mobile vs desktop. Mobile will sometimes use the metadata to orient the picture correctly. Desktop will not.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4
GMN Approved Links!


www.rockauto.com www.adtr.net