PotM GrandMarq.NET - Panther Headquarters Forum Index PotM
GMN Chat Room GMN's STORE!! GMN's Gallery Please!!
Page 5 of 5 FirstFirst ... 345
Results 81 to 93 of 93

Thread: My 79 Marquis

  1. #81
    GMN Regular slack's Avatar
    Join Date
    Mar 2013
    Location
    Long Island, NY
    Posts
    1,293

    Default

    Quote Originally Posted by Mainemantom View Post
    I would not splice brake lines. In some States, that is not legal.
    Interesting, I didn't know that. I think every vehicle I own at this point has patched brake lines thanks to road salt.

  2. #82
    Member Grand1's Avatar
    Join Date
    Feb 2012
    Location
    Michigan
    Posts
    700

    Default

    Well the proportional valve is definely toast. Was able to get the fuel nut off the broken line and plug it for the time being. It has a decent leak from another fitting now. Wagon man doesnt have any in stock right now, so I will be learning shortly if the Speedway valve will work. Since all the lines are gonna be redone, might as well and replace the master cylinder.....which leaves the brake booster as literally the last part not be replaced. The positive through all of this is that it has been baptism by fire about brakes, learned alot.



    1978 Grand Marquis 460 2door "Blue Bomber"

    1987 LTD Crown Vic 351w aka the "MI Mountie"

    1989 Colony Park ....Marge still lives!

    1979 Marquis creamy goodness

  3. #83
    fomoco panthers !
    Join Date
    May 2011
    Location
    Bangor,Maine
    Posts
    3,853

    Default

    I always change the vacuum booster with the master cylinder.Parts have to have a lifetime warranty though. It saves doing the job twice. I can keep my eye out for a valve. If you have a part number on it, post it. I am sure you could get one via Car-part.com. out west. until you can get a new one.

  4. #84
    all the CFI are belong to me
    Join Date
    Feb 2014
    Location
    Windsor, ON, Canada
    Posts
    1,992

    Default

    Quote Originally Posted by slack View Post
    Interesting, I didn't know that. I think every vehicle I own at this point has patched brake lines thanks to road salt.
    I am fairly sure the legality issue applies specifically to compression fittings as a brake line repair, which I believe is considered to be not legal everywhere that regulations exist surrounding the topic at all.

    If you were to repair a brake line by flaring the end and using a union, there is no functional deficiency that I can imagine unless the line that was left in place was iffy...as for legality, I'm not so sure. It would pass a safety here and Ontario is really picky about stuff, regulating down to the number of drips of a particular diameter over a fixed amount of time that are allowable leaks for various fluids...(easily flammable ones such as power steering allow zero leak of any amount over any time, brake fluid of course also allows no leak over any amount of time).

    Quote Originally Posted by Grand1 View Post
    master cylinder
    If you are replacing the master, you can take care of this problem by doing what I did with my wagon. Go to a newer master cylinder from one of the years that still has disc/drum, but which does not have the frame-mounted demonic garbage valve. I did that specifically to delete the valve. I'll dig for the parts combo I used. If you're hellbent on keeping the OE design I have at least one of those valves kicking around somewhere but I'd really suggest just not doing that.
    Last edited by kishy; 06-04-2021 at 11:13 PM.

    Current: 83 GM 2dr POTM 10/2019 | 84 TC POTM 1/2017 & 4/2019 | 85 CS | 85 Ranger +trlr | 86 GM | 91 GM POTM 12/2017
    Gone: 97 CV | 83 TC
    Junkyards

  5. #85
    Member Grand1's Avatar
    Join Date
    Feb 2012
    Location
    Michigan
    Posts
    700

    Default

    Yeah, thanks for the advice. I did purchase a booster and master might as well. I gave Summit a call and this universal valve will work....we shall see.

    https://www.summitracing.com/parts/w...QaApVXEALw_wcB

    Damn kish, just saw your post.... I have a master cylinder by raybestos( mc39531 part number ) sitting in my garage and actually was looking at replacing it as they look damn similar .... but crossed reffed the part number and didnt see the 79 listed, I deep sixed the idea.

    ....and yes I exercised that demon valve with four letter words
    Last edited by Grand1; 06-05-2021 at 12:05 AM.



    1978 Grand Marquis 460 2door "Blue Bomber"

    1987 LTD Crown Vic 351w aka the "MI Mountie"

    1989 Colony Park ....Marge still lives!

    1979 Marquis creamy goodness

  6. #86
    all the CFI are belong to me
    Join Date
    Feb 2014
    Location
    Windsor, ON, Canada
    Posts
    1,992

    Default

    Quote Originally Posted by Grand1 View Post
    Damn kish, just saw your post.... I have a master cylinder by raybestos( mc39531 part number ) sitting in my garage and actually was looking at replacing it as they look damn similar .... but crossed reffed the part number and didnt see the 79 listed, I deep sixed the idea.

    ....and yes I exercised that demon valve with four letter words
    Ah, well...fixing it "properly" isn't a bad thing.

    For reference if it comes up again, the master I used was an Autospecialty M81052, which is no longer sold.
    If you look up a '91 Grand Marquis, you will find options for "police" or "HD" and also for not police or HD. You also find options for including a reservoir or not; for a retrofit like this, you need the reservoir as you have no existing one to swap over.
    Some of them have a total of two outlets, some of them have a total of three outlets. There is not much consistency, some brands the police one is 2 ports, some brands the non-police one is 2 ports. If you get the 2 port one, you have to use an external splitter (nothing fancy, just turns one line into two) for the front brakes. If you get the 3 port one, you run both front brakes directly to the master. The rear will require a "proportioning" or "residual pressure" valve (depends who you ask as to what it's called) which threads in directly; I got mine from a junkyard as the new ones didn't come with it.

    You also need to junkyard (or otherwise) source the low fluid level sensor which clips into the master and make a minor wiring connection to attach that sensor to the wiring that used to go to the switch on the valve. Not a big deal really.

    These masters use metric threads for the flare nuts and bubble flares. On the late boxes that actually came with these things, it's a little piece of trivia...the other ends of the brake lines use double flares and SAE fittings, but the master cylinder end is all metric. Of course, 3/8 and M10 are close enough that someone not paying attention can put a 3/8 flare nut into the M10 hole, and if you crank it down tight enough, the double flare will seal by digging into the bubble flare seat, so it ends up working even though it shouldn't. In my relatively earlier days of wrenching I did exactly this thing to my 91.
    Last edited by kishy; 06-05-2021 at 12:44 AM.

    Current: 83 GM 2dr POTM 10/2019 | 84 TC POTM 1/2017 & 4/2019 | 85 CS | 85 Ranger +trlr | 86 GM | 91 GM POTM 12/2017
    Gone: 97 CV | 83 TC
    Junkyards

  7. #87
    fomoco panthers !
    Join Date
    May 2011
    Location
    Bangor,Maine
    Posts
    3,853

    Default

    Quote Originally Posted by Grand1 View Post
    Well the proportional valve is definely toast. Was able to get the fuel nut off the broken line and plug it for the time being. It has a decent leak from another fitting now. Wagon man doesnt have any in stock right now, so I will be learning shortly if the Speedway valve will work. Since all the lines are gonna be redone, might as well and replace the master cylinder.....which leaves the brake booster as literally the last part not be replaced. The positive through all of this is that it has been baptism by fire about brakes, learned alot.
    I have located a nos proportioning valve. You have a pm.

  8. #88
    Member Grand1's Avatar
    Join Date
    Feb 2012
    Location
    Michigan
    Posts
    700

    Default

    Thanks!

    And finally some progress.
    Click image for larger version. 

Name:	20210606_145123.jpg 
Views:	19 
Size:	315.9 KB 
ID:	56434



    1978 Grand Marquis 460 2door "Blue Bomber"

    1987 LTD Crown Vic 351w aka the "MI Mountie"

    1989 Colony Park ....Marge still lives!

    1979 Marquis creamy goodness

  9. #89
    GMN Regular DerekTheGreat's Avatar
    Join Date
    Sep 2014
    Location
    Warren, MI
    Posts
    6,394

    Default

    I'm late to the party here but one of the methods I use to remove brake lines and their fitting is to cut the line right at the fitting and then use a six point socket on it. This is my go-to method for any line I intend on replacing. I might try a line wrench, but if there's even a wiff of rust & decades, round-off is nearly guaranteed.
    1985 LTD Crown Victoria - SOLD
    1988 Town Car Signature - Current Party Barge

  10. #90
    Member Grand1's Avatar
    Join Date
    Feb 2012
    Location
    Michigan
    Posts
    700

    Default

    So bad lock ring? O ring got bunched?
    Or fuel tank sending unit decayed around the edges? Drips from the very bottom. Guess I will drop it.

    Anyone know a good source for new fuel tank sending units? Float is toast in this one.

    Click image for larger version. 

Name:	20210612_194536.jpg 
Views:	16 
Size:	47.9 KB 
ID:	56475
    Last edited by Grand1; Yesterday at 08:25 PM.



    1978 Grand Marquis 460 2door "Blue Bomber"

    1987 LTD Crown Vic 351w aka the "MI Mountie"

    1989 Colony Park ....Marge still lives!

    1979 Marquis creamy goodness

  11. #91
    2 decades of DDing Box Panthers, now in a Whale VicCrownVic's Avatar
    Join Date
    Nov 2012
    Location
    Shelby Township, MI
    Posts
    3,505

    Default

    Remind me and I'll bring you a good float next weekend.
    Get some Permatex Motoseal for the sender gasket, that's what we ended up using when we replaced the pump/sender hanger assembly on The Ice Car.
    Kishy had found a source for sending units but I'm not sure if it was right for carb application.

    That sender is doable without dropping the tank.
    Vic

    ~ 1998 Mercury Grand Marquis LS - new DD
    ~ 1991 Mercury Grand Marquis LS "The Scab" - plenty of rot, summer DD
    ~ 1997 GMC Yukon - wannabe winter DD - returning sometime in the 2020s, I finally have an engine
    ~ 1991 Mercury Grand Marquis GS "The Ice Car" - Rotting Retired Winter DD
    ~ 1989 Mercury Grand Marquis GS - Rotting Retired DD
    Gone but not forgotten:
    ~ 1988 Country Squire ~ 1987 Ford Crown Vic

  12. #92
    Member Grand1's Avatar
    Join Date
    Feb 2012
    Location
    Michigan
    Posts
    700

    Default

    Thanks Vic!
    I will get ahold of Kishy about the sending unit. Looking forward to the Repairathon.

  13. #93
    2 decades of DDing Box Panthers, now in a Whale VicCrownVic's Avatar
    Join Date
    Nov 2012
    Location
    Shelby Township, MI
    Posts
    3,505

    Default

    From this thread
    http://www.grandmarq.net/vb/showthre...ding-Unit-Carb
    you can probably track a sending unit down. Part numbers sprinkled throughout that thread.
    Vic

    ~ 1998 Mercury Grand Marquis LS - new DD
    ~ 1991 Mercury Grand Marquis LS "The Scab" - plenty of rot, summer DD
    ~ 1997 GMC Yukon - wannabe winter DD - returning sometime in the 2020s, I finally have an engine
    ~ 1991 Mercury Grand Marquis GS "The Ice Car" - Rotting Retired Winter DD
    ~ 1989 Mercury Grand Marquis GS - Rotting Retired DD
    Gone but not forgotten:
    ~ 1988 Country Squire ~ 1987 Ford Crown Vic

Page 5 of 5 FirstFirst ... 345

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
GMN Approved Links!


www.rockauto.com www.adtr.net