|
| GMN Chat Room | GMN's STORE!! | GMN's Gallery | Please!! |
Activity Stream
-
Older Activity
-
Today, 08:25 PMhttps://www.kijiji.ca/v-classic-cars/ottawa/for-sale-1981-mercury-marquis-brougham-15214-original-km/1617995188653 replies | 175873 view(s) -
Today, 08:12 PMGiraffe replied to a thread Moog Problem Solver (private label) parts at RockAuto in Internet Rare Finds and Good DealsI bought an upper ball joint once that was missing the dust boot entirely. It’s a gamble, but a sensible one.2 replies | 92 view(s) -
Today, 07:50 PMMainemantom replied to a thread My Rare and Interesting Findings. in Internet Rare Finds and Good DealsI think this one is for no strips. Buyer needs to verify with Ford.2294 replies | 324245 view(s)
-
Today, 06:13 PMhttps://www.ebay.com/itm/165492881984?epid=1823391419&hash=item268824fa40:g:E0EAAOSwXmJiiBoP2294 replies | 324245 view(s) -
Today, 05:48 PMWhen I see something done cleanly like that I like to imagine that the car has lived a good life while under that persons watch.2294 replies | 324245 view(s)
-
Today, 05:32 PMno. Do not fuck with the injector wiring under any circumstances ever. The fuel trims will be incorrect. Less harm from leaving it with the wrong...12 replies | 327 view(s) -
Today, 04:42 PMHi all. I'm doing an 01/02 ABS install in my 86 Crown Vic cpupe. I am having an issue verifying brake line positions off of the module. My module has...0 replies | 30 view(s) -
Today, 02:39 PMI’d be willing to bet that if you were a REAL miser, you could simply change the fuel injector wiring to match the HO firing order and it would...12 replies | 327 view(s)
-
Today, 01:19 PMyeah once you approach proper rolling torque it goes from nothing to in spec in a pretty small amount of big wrench travel.13 replies | 213 view(s)
-
Today, 11:07 AMno you most likely need a 1/4" beam torque wrench and 2 square drive adapters. 1/2male to 3/8 female and 3/8male to x1/4female ...13 replies | 213 view(s)
-
Today, 10:22 AMCan you get a 1/2 drive torque wrench that goes down that low (8-14 lb-in)?13 replies | 213 view(s) -
Today, 09:35 AMThere is a procedure for R&R of the flange. If you're doing nothing else, change the seal while you're at it, they're like 3 bucks. Basically the...13 replies | 213 view(s)
-
Today, 09:26 AMgadget73 replied to a thread Moog Problem Solver (private label) parts at RockAuto in Internet Rare Finds and Good DealsI've got most of a front end rebuild for the Towncar from a prior one of these. Good parts, but as mentioned sometimes the boots are questionable. ...2 replies | 92 view(s)
-
Today, 07:09 AMI checked the vacuum dump valve, it didn't leak. Then I just jiggled the black box and servo connectors and now it works again. Yay! Had a longer...749 replies | 82139 view(s) -
Today, 01:39 AMYeah those gauges look really nice there. Definitely one of the cleaner locations I've seen on these cars. Cropped from eBay listing:2294 replies | 324245 view(s) -
Today, 12:19 AMkishy started a thread Moog Problem Solver (private label) parts at RockAuto in Internet Rare Finds and Good DealsJust noticed RockAuto seems to have picked up some inventory of private labeled Moog Problem Solver suspension and steering parts, covering multiple...2 replies | 92 view(s)
-
Yesterday, 08:20 PMMissed the gauges. That's a nice setup for the space.2294 replies | 324245 view(s) -
Yesterday, 07:56 PMThe vacuum release switch is separate from the brake light switch, so you may just have to adjust the vacuum switch if it happened to just back off...749 replies | 82139 view(s) -
Yesterday, 07:10 PMhttps://www.ebay.com/itm/165488613355 Whats cool is the vintage sunpro digital gauge pack that was fitted in place of the drivers side dash vent. ...2294 replies | 324245 view(s)
-
Yesterday, 06:28 PMJust the one plastic line from the dist block to the brake release valve. I put it back and made no difference. The amount of vacuum crap has reduced...749 replies | 82139 view(s)
-
Yesterday, 05:48 PMIf you need tires, and you are okay with the Generals buy them yesterday. Tires seem to be another item hit with the supply chain issues. The new...68 replies | 5822 view(s) -
Yesterday, 04:03 PMLots of vacuum is used for HVAC, Cruise, EGR, and smog. As for removing the feed from the distribution block, are you sure you didn't pull more than...749 replies | 82139 view(s)
-
Yesterday, 03:59 PMI only ever edit the OP on threads like some of the stickies or my own threads but always put an additional post in the thread stating the change so...3 replies | 92 view(s)
GMN Approved Links!
|
|