I went to the machine shop where my engine is getting worked on and he told me he polished .002" off it and it still had marks from where the oil broke down. I saw them for myself, I'm just trying to figure out what could have caused them. I over-heated twice but I don't think gas ever got in the motor, unless something was wrong with my fuel injection.
 |
-
1989 Lincoln Town Car - "Anabelle" - Original block, .030 over with SpeedPro pistons, rods fitted with ARP hardware, FRPP +volume oil pump, GT-40 3bar heads, Crane 1.72 rockers, 89' Fox cam, 93' Cobra lower intake, Explorer upper and 65mm TB, 93' Lightning EGR spacer, K&N intake kit from a 4.0L Ranger, 19lb/hr injectors w/ 87 Mark VII ECM, cat/smog deletes, Big Brake conversion, 3.55 K-Code Trac-Lok/Disc brake rear axle, CVPI LCA's w/1" sway bar in rear, wagon front sway bar, BBK 2.5" off-road H-Pipe, Flowmaster super 40s, HPP wheels, 3G alternator w/LMR.com wiring kit, gear reduction starter conversion, Best 1/4 time: 16.0 @ 85mph. -
Grind .010.... put undersize bearings in.....don't sweat it....
Even .020 under is absolutely no big deal..... -
yeh have it cut to the next standard undersize. .010 or .020 is typical and nothing to worry about.
Probably dirt in the oil is what scarred it up. If it didn't have really regular changes, or if it wasn't changed right after it was overheated and you sucked up an oil crunchy that got pumped through the bearings, thats probably what happened. I'll bet your bearings are scratched up pretty good too.86 Lincoln Town Car (Galactica).
5.0 HO, CompCams XE258,Scorpion 1.72 roller rockers, 3.55 K code rear, tow package, BHPerformance ported E7 heads, Tmoss Explorer intake, 65mm throttle body, Hedman 1 5/8" headers, 2.5" dual exhaust, ASP underdrive pulley
91 Lincoln Mark VII LSC grandpa spec white and cranberry
1984 Lincoln Continental TurboDiesel - rolls coal
Originally posted by phayzer5
I drive a Lincoln. I can't be bothered to shift like the peasants and rabble rousers
Everything looks like voodoo if you don't understand how it worksComment
-
Yeah there was some crap in the bottom of the pan that looked like old hard gasket material.... Its getting turned 10 thousandths.1989 Lincoln Town Car - "Anabelle" - Original block, .030 over with SpeedPro pistons, rods fitted with ARP hardware, FRPP +volume oil pump, GT-40 3bar heads, Crane 1.72 rockers, 89' Fox cam, 93' Cobra lower intake, Explorer upper and 65mm TB, 93' Lightning EGR spacer, K&N intake kit from a 4.0L Ranger, 19lb/hr injectors w/ 87 Mark VII ECM, cat/smog deletes, Big Brake conversion, 3.55 K-Code Trac-Lok/Disc brake rear axle, CVPI LCA's w/1" sway bar in rear, wagon front sway bar, BBK 2.5" off-road H-Pipe, Flowmaster super 40s, HPP wheels, 3G alternator w/LMR.com wiring kit, gear reduction starter conversion, Best 1/4 time: 16.0 @ 85mph.Comment
-
have them hot tank the sheetmetal so there is no chance of assembling a new engine with old junk that may fall off
1986 lincoln towncar signature series. 5.0 HO with thumper performance ported e7 heads, 1.7 roller rockers, warm air intake, 65mm throttle body, 1/2" intake spacer, ported intakes, 3.73 rear with trac lock, 98-02 front brake conversion, 92-97 rear disc conversion, 1" rear swaybar, 1 3/16" front swaybar, 16" wheels and tires, loud ass stereo system, badass cb, best time to date 15.94 at 87 mph. lots of mods in the works 221.8 rwhp 278 rwt
2006 Lincoln Town Car Signature. Stock for now
1989 Ford F-250 4x4 much much more to come, sefi converted so far.
1986 Toyota pickup with LSC wheels and 225/60/16 tires.
2008 Hyundai Elantra future Revcon toad
1987 TriBurner and 1986 Alaska stokers keeping me warm. (and some pesky oil heat)
please be patient, rebuilding an empire!
Comment
-
its been hot-tanked, magnafluxed, cleaned and bored. Got new cam bearings, and all new freeze plugs installed.1989 Lincoln Town Car - "Anabelle" - Original block, .030 over with SpeedPro pistons, rods fitted with ARP hardware, FRPP +volume oil pump, GT-40 3bar heads, Crane 1.72 rockers, 89' Fox cam, 93' Cobra lower intake, Explorer upper and 65mm TB, 93' Lightning EGR spacer, K&N intake kit from a 4.0L Ranger, 19lb/hr injectors w/ 87 Mark VII ECM, cat/smog deletes, Big Brake conversion, 3.55 K-Code Trac-Lok/Disc brake rear axle, CVPI LCA's w/1" sway bar in rear, wagon front sway bar, BBK 2.5" off-road H-Pipe, Flowmaster super 40s, HPP wheels, 3G alternator w/LMR.com wiring kit, gear reduction starter conversion, Best 1/4 time: 16.0 @ 85mph.Comment
-
Was the block after you get it back brush out the oil galleys. Hot tanks sometimes leave crap in the motor from other peoples motors.Scars are tatoos of the fearlessComment
Comment