If this is your first visit, be sure to
check out the FAQ by clicking the
link above. You may have to register
before you can post: click the register link above to proceed. To start viewing messages,
select the forum that you want to visit from the selection below.
Please let us know if things are working or not. This is still somewhat a work in progress so don't be too surprised if things magically appear from one visit to the next.
well they (manual cutouts) would be a fuck of a lot cheaper if you could do the fabrication yourself. come to the muffler shop and i'll rig some up for you for free.....the several days travel time might make it not worth it though
sigpic
- 1990 Ford LTD Crown Victoria P72 - the street boat - 5.0 liter EFI - Ported HO intake/TB, 90 TC shroud/overflow, Aero airbox/zip tube, Cobra camshaft, 19lb injectors, dual exhaust w/ Magnaflows, Cat/Smog & AC delete, 3G alternator, MOOG chassis parts & KYB cop shocks, 215/70r/15s on 95-97 Merc rims
This is my first attempt to use this video recorder. I never had one before.
This thing makes the engine sound noisey but the door click when opening puts it in to perspective.
The inside hasn't been cleaned yet since changing the heater core.
sigpic
89 LTC 429>557 Cobrajet stroker
13 F-150 XLT 6.2 l
"If I could separate what's real from what I've been dreaming I could live to fight another day"
Summer car-> 1988 Lincoln Town Car, triple blue, 335,xxx km. New HO 5.0 in and running. Bought 2006/08/22. June 2017 PotM!
Winter vehicle-> 1995 Ford F-250 XLT SuperCab 4x4, 284,xxx+km. AKA "Brutus" 460/E4OD/4.10 axles and 12 MPG. Bought 2019/08/14
Originally posted by phayzer5
I drive a Lincoln. I can't be bothered to shift like the peasants and rabble rousers
The exhaust is in.
Still havn't went over the bottom of the car yet. I need to get out the wire brush and rust remover then the reformer. Good thing this will never see salt again!!!
Summit h-pipe Flowmaster S bends and impala tails with aerochambers.
I did put a small 0.5" notch on the driver's crossmember at the #6 tube. After they were torqued down it looks like I didn't need to. There is a 0.75" clearance there now and the engine pulls away from that side.
I did get a video recorder finally so I need to get one up here.
Are those FPA headers? I think I recall them being not very nice to Tom when he called them about headers for his BBF two-door project.
Builder/Owner of Badass Panther Wagons
Busy maintaining a fleet of Fords
Yup, FPA headers. I ordered from the owner over the phone. He asked me all about my car we were on the phone about half an hour. Nice chat, and he was also happy to hear back from me that they fit. Seemed like a stand up guy?
Thanks for all the positive feedback!!!
sigpic
89 LTC 429>557 Cobrajet stroker
13 F-150 XLT 6.2 l
"If I could separate what's real from what I've been dreaming I could live to fight another day"
About 20 min drive to salem ohio. Aboout 1 hr 15 min to Nelson's Ledges.
I would love to go on a test and tune day to get my ignition timing dialed in.
sigpic
89 LTC 429>557 Cobrajet stroker
13 F-150 XLT 6.2 l
"If I could separate what's real from what I've been dreaming I could live to fight another day"
Got the a/c in now. I'm very happy with it. I was worried that it might not keep up with the heat that thing makes. Keeps it nice and cold inside. Hope it still does with 90f humid days.
There is a shot of the header and evap spacing. With the box modified in as far as I was able, there is still only 1/2" gap. This heat shield works. It isn't showing any heat damage after quite a few hours of exposure.
Makes it a little more cluttered but you HAVE to have working a/c before going to the track. You might get hot driving up to the starting line before you shut it off to have fun.
sigpic
89 LTC 429>557 Cobrajet stroker
13 F-150 XLT 6.2 l
"If I could separate what's real from what I've been dreaming I could live to fight another day"
Comment